Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are durable, long-lasting and easy to maintain. They do not get rotten or rusty like aluminum and timber.

Regularly cleaning and lubricating UPVC windows and doors is vital. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and may even be fatal. It is important to take the time to make sure that you are doing everything you can to ensure that your windows are in good condition.

For single pane windows, it is fairly easy to replace them, and the new window will generally fit within the frame of the previous one easily. However If you have double pane windows that are held in place by internal beading, it'll be more difficult to remove the existing panes and install new ones. In this situation it is essential to purchase plastic spacers in order to aid in fitting the new pane into the window repairs near me frame.

Wearing eye protection and heavy gloves is a must if you plan to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not on the floor, where they could be trampled.

Once the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and fix the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is large, you may be interested in an alarm door that comes with an integrated window, as this will offer the best of both worlds.

2. Sagging

uPVC is a durable, energy-efficient and affordable alternative to timber sash windows. However, with time, they may be afflicted by a variety of issues, including sliding. A sagging window can cause problems with light, draughts or even security. It's important to take action immediately if you realize that your uPVC windows are sliding.

To fix a sagging window you can try repositioning the hinges. You'll first need to open the windows so you can get at the frame. Then, remove both the hinges at the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to check the fit after you have repositioned your hinges. If you're satisfied with the fit, tighten the screws to ensure they remain in the right place.

If you are unable to reposition the hinges, you may require replacing the seal. Over time rubber seals can lose their elasticity and become dry which causes them to loosen. If this happens, it's important to replace the seal as quickly as possible so that your uPVC windows remain watertight and draught-proof.

uPVC handles can also loosen up. The majority of the time this is due to screws that have become loose over time. However, it can also happen because the handle mechanism has worn out. It's relatively simple to repair a loose uPVC handle. You'll first need to close the window and then perform an initial fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism to position.

3. Water Leaks

It is important to act if you get up each morning to find a smoky wall and wet floors. Water leaks from windows can not only cause degradation of your home's structure but also undermine your efforts to control the temperature in your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or not present.

This is an easy fix that can be done by any DIYer who is competent. Based on the severity of the problem the old caulking may require removal before a new layer can be put on. It is crucial to remember that when it is about uPVC window repairs, do avoid the temptation to "over-caulk and then make the area harder to clean and could reduce the efficiency of your energy.

Verify that the drainage holes do not have debris in them and ensure that the sill pan has been properly angled to drain away from the window. In more severe situations, you may have to replace the window.

Moldy sills and rotten ones are another sign of water leakage. This fungus thrives in damp conditions and is able to quickly spread throughout the home.

It is also important to remember that if the leak originates from the glass in your double glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sagging. This can be easily fixed by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and blow open with ease, it may be the hinges that are at the fault. They can be replaced by any competent DIYer and are usually done within a few minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that have hinges and like any mechanical part they can wear down over time. It's easy to change the hinges on a window, but it's easier if someone helps hold the frame.

Make sure that the uPVC hinges are open and closed in the right direction. You can do this by looking for the arrows on each hinge. This indicates which way the window should be opened.

Faulty window hinges can be caused by incorrectly opening the window in a particular manner or because of improper installation in the factory. This can often be resolved by sending us a picture via our website and we will be happy to give you advice.

Regularly lubricating hinges is also essential. Applying an engineering lubricant that is light to the hinges is a good method of doing this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It also helps prevent corrosion and reduce the risk of sticking. The ideal time to perform this every year. WD40 or other solvent-based oils should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a few different things. The hinges may also become misaligned due to wear, which can cause a gap where the sash meets frame. They can be repaired by giving them thorough clean, however in the event that they are beyond repair it may be necessary to have them realigned or replaced. Secondly the interlock, this is located on the hinge of the window and can also be misaligned, and again it's possible to give them a good clean, but in some cases it might be necessary to have these replaced.

The next common reason for draughts is window seals. They can become worn down or damaged over time, and let air escape through these gaps. Installing high-quality weatherstripping can help keep draughts at bay. Replace the windows made of Upvc with low-emissivity lenses. This will help control indoor temperatures and decrease the risk of draughts.

Another method of reducing the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler, which can be put on top of your window sill. These will help to block out cold air and keep your home warm and cosy!

Your upvc window repair near me windows can keep providing excellent insulation and security in your home with regular maintenance and repairs. It is essential to remember that all windows will eventually get worn out and it may be more cost-effective to simply replace them rather than repair them. If you are experiencing issues with your window made of upvc window repairs you should consult a professional as soon as possible.