Replacing uPVC Window Handles

It is simple to swap the handles on windows made of upvc. It is important to ensure that the replacement handle is fitted into the spindle cutout in the window mechanism.

If you follow the steps below, any cockspur handle will fit on most windows. The key is the step height of the handle.

What to Do You Look For?

A lot of windows in the UK are fitted with uPVC handles and, over time, they can begin to show signs of wear and tear. When this occurs, the window handle can become loose or difficult to operate, making it necessary to replace it. Anyone who is proficient with basic hand tools is able to complete this job.

The first step is to make sure that the handle is securely attached to the frame of the window in the open position. The next step is to locate the fixing screws or pins that hold the handle in the position it is in. They are usually located on the inside face of the handle and can be removed using a screwdriver or pliers.

Once the handle has become loose it can be taken from its hinges by gently pulling it off. Then, you'll have to locate a replacement handle in the same style and size. This can be done in the DIY store or on the internet. The process should take about five minutes, and you will need a screwdriver is all you need.

When replacing the handle on a uPVC handle, it is important to think about the step height. This is the distance from the bottom of the handle to where it is placed on the frame of the window. This is a standard measurement and you should check the step height before ordering a replacement handle.

There are various sizes depending on the kind of handle. Inline handles for uPVC windows typically feature lug centers of 31mm, and there are also varieties of cockspur handles with 43mm centres. Tilt-and-turn handles are common on uPVC Windows. They feature a unique design which allows the window be tilted for ventilation and then rotated to fully open the window.

The most common uPVC handle cracks are internal, instead of a break at the base. This can make them hard to open and is why it is crucial to ensure that the replacement handle you buy has the same spindle length as your existing one.

Remove the old Handle

Incorrectly fitted or damaged window handles may cause your double glazing handles-double glazed handles windows to open and close improperly and could even cause them to become stuck. There are a variety of reasons for this including general wear and tear or corrosion of the handle. In these situations it is crucial to seek replacement handles made of upvc immediately to prevent further damage and loss of functionality.

When replacing upvc windows handles it is recommended to remove the old handles from the window. To do this, begin by taking off the screw that is encased when the handle is in a closed position. After you have removed the screw, you can remove the handle. It is a good idea to make use of an electric screwdriver for this, as it makes the task easier and quicker.

It is also important to note that the screws on the handle may be hidden behind plastic caps, so it is a good idea to take the Stanley knife to the screw covers and remove them. After removing the handle, you'll have to examine the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. This is important because you'll need to measure the length of the spindle on the old handle to ensure that it is in line with the size of the window mechanism and the handle spindle cut out.

The various types of upvc window handles are: Espag bi-fold doors handles, which have a central screw and can turn left or right; Cranked handles which have two screws and are typically found on tilt and turn upvc windows as well as Spade handles, that have an arm with a flat surface and can be put on either side of the window. It is easy to replace the handle once you have found one that is suitable. Simply put it in place and ensure that the spindle is correctly inserted into the lock mechanism. Once you have done this you can tighten the handle onto the window frame. Your replacement upvc handles should now be secured.

Take a measurement of the Spindle

If you're looking to replace a upvc handle that has fallen, it's likely the spindle that holds it in place is damaged or is loose. In some cases this can be fixed using pins or screws to tighten it. In certain situations it might be necessary to replace the handle. There are many types of upvc window handles. They include espagnolette handles inline as well as cockspur handles. tilt and turn handles. Each type of handle is mounted and replaced in a different way.

It is essential to measure the current handle before purchasing an alternative. This will ensure that the handle fits the window in a proper manner and will be of the correct size. All handles are measured in accordance with industry standards, so it is easy to determine the right size.

To measure the handle's size, turn the window to the open position. You should be able see the size of the pin or screw that secures the handle. Make use of a ruler or tape measure to determine the length the spindle is. Once you know the length of your spindle it is possible to purchase a replacement of exactly the same size.

The step height of a window handle is also important to take into consideration when purchasing replacements. The step height is measured from the base to the point where the handle is positioned on the frame. Typically, this is about 21mm for uPVC windows or 9mm for aluminium. To make sure that the new handle is suitable it, you can drop something into the gap to check the distance it will go before it meets an obstruction.

Cockspur handles can have different backsets, based on the style of window you install them in. Inline the espag handle heights range from 43mm from centre to centre (two fixing points). Cockspur handles have different backsets depending on the type of window they are located in. This is due to the fact that they have a spur which extends from the handle and is locked onto a cockspur wedge hitting plate.

Fit the New Handle

When you've picked a new handle, make sure you align it with the screw holes on the patio door handle replacement and secure it with the screws supplied. If you're replacing the latch lever it can be put in similarly to the main door handle. Finally, reattach the door trim in order to conceal the mounting screws and close off your project.

Tips: To remove the metal head from a wedge made of wood, place the handle on the floor so that its wide end is level with the ground. Then, use a hammer and tap the narrow end. Be careful not to scratch the handle or spindle.