how to program saab 9-3 key fob to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of specific steps to add an additional ignition key. This requires an electronic handheld computer, referred to as Tech-2 which is used by the dealer. Then a new key and transponder need to be bought and then programmed to the car.

It is recommended to rotate your keys so that one does not wear out more quickly than the other. This will help to keep your keys in pristine condition.

Replacement Case

Contrary to the classic saab key fob repair keys of old keys, the new key fobs have electronics inside which makes it hard to duplicate. This has made theft of cars significantly more complicated than it was 20 years ago. It has also made it more expensive to replace lost keys.

Every owner of a 9-3 Saab 9-3 key should have at a minimum two functioning keys. It's expensive to replace a lost or damaged key since it requires replacing the CIM module, as well as reconfiguring the locking cylinders. Dealers usually charge between $100 and $200 to do this.

There are options to avoid these costs. Some parts retailers will find the code from an old key (usually the same one that opens the doors and turns off the ignition) and cut a brand new metal key blade at less than the dealer's cost. The key, however, must be the same as the original one in order to function within your car.

Follow these steps to replace the case. You will need an flathead screwdriver and patience. With the screwdriver slowly break the plastic and then separate the emergency key from the case. After the case is open remove all electronics and put them back in your new case. Put the correct key and badge inside the case.

Replacement Battery

The saab key fob replacement 9-3 replacement battery is a budget component that can be quickly and easily replaced. This YouTube tutorial for DIY Cyclone Cyd, a user on YouTube, explains how to replace the battery for the remote key fob in just four steps. This tutorial will work with any modern Saab key fob. However, the process may differ slightly.

The button is normally located near the Saab logo on the back of the fob. This button is usually located on the back of the fob, close to the Saab Logo. Then use the flathead screwdriver to insert into the small hole of this button. This will be enough to allow you to open the case of the fob so that you can replace the battery.

After you have installed the new CR1632 batteries, you can reassemble the remote key fob. You can then program it into your car. The entire process shouldn't take more than an hour. It's a very easy procedure that doesn't require any special equipment.

The process can be a bit more complex if you lose your key, but it is possible. The dealer has to read the car's VIN and then order a replacement key blade and TWICE module with the exact unique code. The dealer will then have to program the key using MDI, a brand new software tool.

Replacement Key Fob

The key fob contains a battery that is used to lock and unlock your vehicle. The batteries last for a certain time that is a long time, and they eventually go out of service. It is a common problem that affects all cars. The good thing is that you can change the batteries in most key fobs, and not have to replace the entire case. Amazon sells replacement fobs that already have all the electronic components in place. You can simply pop the case open and replace the batteries. You'll need to take out the emergency key before you replace the batteries. To accomplish this, simply insert the screwdriver of a small flat head into the slot that is in the middle. The case should split when you work the screwdriver all around it.

If you're looking to replace your keys, be sure to have a spare in your possession. This will save you a significant amount of money. If you have a spare, you can ask the dealer to cut the new key and program it to your car, which is much cheaper than replacing the whole key fob.

If you do not have a spare key, it is possible to add a second key to your car, however this requires a lot of research and effort. Adding a second key costs a few hundred dollars, and it requires programming of the car's computer. This can be done by a professional, however it's a costly choice for the majority of owners.

replacement saab car keys Ignition

The new SAAB 9-3 uses an alarm system that is more sophisticated built on a keycode. This means that should you lose only one working key, adding another one could be very expensive since the car has to have a special computer module fitted and also needs to be specifically programmed to accept a new key. Locksmiths typically aren't able to program this and a dealer will charge several hundred dollars to program the new key!

Dealers will charge you the highest price to replace your car's computer (also called the CIM or SAAB twice) in the event that you lose your only functioning key. We can reprogram the current EEPROM inside your car's computer so that it is ready for an extra key. This will save you more than 50% of the cost you spend at a dealer.

If you've been an owner of an 03-11 SAAB 9-3, you probably realize that the ignition key isn't really all that durable. They can get extremely sticky and the buttons can be removed from them every now and then and you should think about buying a new one if the one you have isn't working properly. It's not as difficult as it seems to replace the ignition key. With the appropriate tools, it could be accomplished quickly.