Double Glazing Door Lock Repairs

Are your uPVC door or window mechanism not working properly? Maybe the window or door handles aren't aligned properly or are hard to use.

You'll be wasting energy when your double-glazed doors do not function properly. This can also increase the chance of burglary. Owen the Locksmith can repair your door lock at an affordable price.

Snapped Key

It can be a hassle when a key gets stuck inside a lock. It's also potentially an issue for security, since the door may not be locked and could leave you vulnerable to burglars. There are a few quick solutions you can use to resolve the issue and make your door functional again.

Keep calm. If you panic and start doing a lot of fumbling around, you might just end up pushing the damaged piece of the key deeper into the lock, which could make the situation even more difficult.

Next spray WD-40 or another penetrating oil into the lock to help the broken piece slide out more easily. You can also use a screwdriver to help break up any stuck pieces that might be blocking the way. If you have a piece of the key still sticking out then grab it using a paperclip or another thin metal object and pull it. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have any of these, you can bend a hook with needle-nosed pliers. You can also use a pair of tweezers grab and pull out the remaining pieces of broken keys.

If you're unable to pull the broken piece of the key out, try using a lock de-icer. It's available in many hardware stores and is used to freeze any moisture present within the lock.

If none of these solutions work, it might be time to consult a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and broken keys with uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to make them easier to operate. You can schedule a double-glazing repair online or contact us to discuss your requirements.

Broken Cylinder

A damaged cylinder could pose a serious security risk. It's fortunately a simple repair for an expert locksmith to complete. A locksmith will have to tap the cylinder in order to repair it. This can be accomplished with a hammer, or any other tool. However, the most effective method is to use a wire or a long match. Then, place the match's tip or wire near the keyway. After this, the locksmith will strike the lock and break it open. This is better than using a hammer that could harm the lock.

The most frequent cause of cracks in the cylinder head is overheating. This can occur when the block and cylinder head are made of different metals such as cast-iron and aluminum. When various metals heat up and cool down at different rates, it can create hotspots locally that expand faster than the rest of the head of the cylinder, leading to cracks.

Another possible cause for cracks in cylinders is corrosion. If the head and block of the cylinder are not maintained in a timely manner they could rust or corrode, which can cause them to expand more than expected. As time passes, this may also lead to cracks.

If your uPVC window or window replacement near me door lock is brittle or requires an enormous amount of pressure to turn, it can be the result of several things. A malfunctioning locking mechanism, misalignment or the wear of the handle are typical reasons for this issue.

This is a simple and cost-effective fix that a majority of double glazing owners can accomplish. A professional locksmith will usually solve this issue within an hour of arriving at the property. Depending on your needs they can change the locking mechanism, change the window handles, or change the gearboxes. A professional locksmith will always be able to advise you on the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security Euro cylinders, TS007, that will provide an extra layer of security against burglars. It is a small cost to get the peace of mind that comes from knowing your uPVC door is secured.

Broken Handle

Window handle locks are complex mechanisms that become less effective with time and use, so it's no surprise that they sometimes break. It isn't easy to determine the cause of the problem and repair it correctly.

Fixing the broken handle, whether it's an internal locking mechanism or latch will increase the security of your uPVC door and reduce the risk of draughts. It can be expensive to replace or repair your handle incorrectly and it could also harm the frame and the lock of your door.

With the window in the open position and the window open, loosen the screw that holds the handle using the screwdriver. The screw should be on the inside of the back plate, and is normally concealed by a screw cover for aesthetic reasons. Be careful not to lose any internal parts within the handle, such as the levers or plates on the opposite side of the spindle. Keep them in the same arrangement to make it easier to replace if necessary.

Then, with another screwdriver loosen the screw that holds the handle to the spindle in the back. Once the screw is loose, you can pull the handle out and take the broken spindle out. Replace it with a new spindle, making sure it's the same length (you can find them online or at hardware stores). Securely screw it into the correct position. Do not tighten the screw too much as this could damage the handle and the window frame.

Close the handle and try it. It should function smoothly, and you will be able to open your window once again.

While you're working on the handle, be sure to ensure that your uPVC windows are closing properly. If they don't close properly, you could experience damp or draughts in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can adjust the hinges of the frames of your windows to ensure that they close correctly.

Broken Spindle

It is more typical for the spindle to break rather than the handle. This is most frequent in uPVC tilt and turn windows. These windows require a handle to operate an electronic locking mechanism within the frame of the window. The handle is connected to a central rod that triggers the locks that are shaped like mushrooms and secure the window frame keep. If the dead latch mechanism does not open when the handle is turned it is likely that the spindle has been damaged and this could be a very frustrating issue.

Fortunately, there are steps that can be taken to rectify this issue. A reputable locksmith will be able to quickly and effectively address this problem. They can disassemble the window handle by using a tool that can remove the wheel portion of the mechanism, where the spindle goes. This can be done without causing any damage to the handle or causing any other damage to the window doctor frame.

After the wheel has been removed the technician can then examine the spindle to determine what caused it to break. This involves breaking the spindle into its constituent components and carefully observing their general condition as in addition to any specific areas of wear or damage. This process is usually carried out by technicians in an environment that is clean.

The next step is to clean the damaged spindle. This will remove any debris or dirt that might be hindering its normal operation. Following this the spindle is cleaned, it could be repaired or replaced. If it is replaced, the technician can take the dowel that is similar in size to the one used in the first and drill mating holes in both pieces of the spindle. This will ensure that the spindle fits perfectly with the handle.

If the damaged spindle cannot be repaired, it could require replacement. Home centers sell generic replacements but if the design of your Window replacement near Me is unusual then it will be necessary to contact a wood worker or cabinet maker who can replicate the exact component for you. Once the spindle has been installed, it is attached to the handle. Line up the screw holes on the handle to the screws that are already in the frame. Once the handle is securely seated, you can operate your uPVC windows.