Window Handle Repair

Window handles can become loose or even broken, allowing the windows open to burglars. It's usually not difficult to fix.

Remove the plastic caps on the top and bottom of the handle. This is a simple job that will take just five minutes with the help of a screwdriver.

Loose Screws

Over time a window handle will loosen due to wear and tear or use. If you notice it becoming unstable or you notice that it is difficult to open it and close it, it could be that the screws have come loose and need a bit of tightening. This is a very easy fix that can be completed in a matter of minutes using a screwdriver.

Remove any plastic caps that are covering the screws on the top and bottom of the handle. You can remove them using either a flathead or a fingernail. After the caps have been removed, start with the top screw and tighten it until it is secure. Be careful not to tighten it too much as this could damage the head of the screw. Then, tighten the bottom screw in a similar way. After both screws have been tightened, the handle should feel more stable and be easier to open.

If your window handle feels very loose or the lock paddle is not able to be inserted, then it's time to get an entirely new crank mechanism. Mail order can be purchased from many hardware replacement specialists. It's less expensive than replacing the entire handle. You can also tighten the crank by opening the window and adjusting crank arm until it is aligned with the notch on the track. After carefully pushing in on the handle, remove any trim mounting screws and lift the casement from the window jamb. (Photo 1) You'll have to replace any bent or rusted trim screws. Install the new operator as shown in Photo 5 after comparing it with the previous one to make sure they are in line.

Filling screw holes that are not completely filled with wood before tightening them might be necessary. Filler should be slightly bigger than the screwhole to ensure that it doesn't pierce surrounding wood when it is turned in the position.

Broken Spindle

The spindle on the window handle can become worn after a period of time. This can cause the handle to malfunction or stop opening properly. Fortunately replacing the spindle is an easy and easy fix that can be accomplished by anyone with a few basic tools. It is also crucial to check the alignment of the handle to ensure it is securely in its place.

After cleaning it is an excellent idea to apply a silicone-based grease to the handle and spindle. This will allow it to turn more easily, removing any dirt or debris which might be obstructing the purpose.

Another issue that is common to uPVC casement windows is when the locking mechanism fails. This happens when the handle fails to push the spindle across the wedge block in a proper manner. This could be a major issue as it can prevent your window from opening or Services closing. You'll need to replace the lock or handle.

It is essential to determine the length of the spindle prior uPVC casement windows to buying an alternative. This will allow you to locate the ideal replacement handle that fits the original one. The measurements are usually on the handle's bottom If you can't find them, contact us to determine the model by phone.

You can also buy a complete replacement set of handles with spindles in order to save time and money. They are typically less expensive and can be put in less time.

It could be time to contact an expert if your uPVC tilt-and-turn window remains closed even after you've tried all these solutions. A skilled uPVC expert will inspect the handle for any issues and provide you with a quote for the repair.

Our selection of replacement uPVC handles includes espag, inline key locking, cranked, and cockspur styles. We have a huge selection of both uPVC and aluminium handle designs in a variety of finishes. We can even order in specific styles for you even if we don't have them in stock.

Broken Handle

If the uPVC window handle doesn't open at all, this can be caused by a damaged handle. This usually happens because the handle is cracked internally, which results in it not having an attachment to the spindle and thus unable to operate the window. This is a problem that occurs with uPVC handles. It can be easily fixed by removing the handle and replacing it with a new one.

It will usually require the use of a screwdriver as well as some elbow grease, but it can be done at home without professional assistance. To remove the handle make use of a screwdriver to lift the cap. The screws on the top and bottom should be visible on the handle's base. With the screwdriver tighten the screw on the top until it is securely. Don't over tighten the screw as this could damage the handle and the frame of the glass.

You can replace the second screw once you've made sure that the handle is securely fastened to the base. Make sure you tighten the screw until it is tight. Afterwards, replace the plastic caps on both screws. Your aluminum window handle should be working just as it should.

Another reason why the uPVC window handle might not open is due to a stripped gear within the cranking mechanism. The handle can turn but not move the window, which can cause a lot of frustration and is also dangerous for your security. In this situation you must replace the mechanism that controls the handle.

This is a fairly easy process that should take more than a few minutes to complete. However, if you're not confident in this task or would prefer hiring experts, the staff at Bridgewater Glass are happy to assist. We have plenty of experience with replacing and repairing handles made of uPVC and can ensure your windows are safe and functioning. Contact us for more information about our services.

Broken Base

A window handle can become loose as time passes. It can sometimes cause the window to slide or tilt when it is opened. If this is the case it usually means that one of the screws is not fastening the mechanism to the frame. It is easy to fix. Just loosen the screw using the hand screwdriver, then tighten. Then close the window and then move the handle back to its original position.

Sometimes, the handle can completely be separated from the base. This is a possibility with both tilt-and-turn and standard handles. It is a rare occurrence and occurs only in areas where it is heavily used. Fortunately, it is an easy fix that can be done with a new replacement.

Another common problem is the stripping of the handle teeth. This is typically the case of older windows with a crank handle. The teeth are typically constructed from cast iron, and may be worn away by the use of a lot or age. This is a simple fix that can be done using small vice grips or a pair pliers.

If your handle breaks away from the base, you will need to take the crank off to replace it. This is a bit difficult for the beginner DIYer, but with a little effort, you can accomplish it.

First, remove the screw that holds the crank operator to the frame of the window. Open the window so that the guide bushing on the crank arm aligns with a notch on track. Then, using pliers, remove the guide bushing off the crank arm.

After removing the old handle, check the crank stud to determine if the teeth are worn. Then, look over the handle for signs that it's worn. Family Handyman advises that if the splines are worn out it is recommended to replace the window crank handle.

Attach the trim cover as well as any screws that are rusted to the frame before installing the new window crank handle. Make sure that the mounting screw holes are aligned with the holes for mounting on the new handle and then attach the base plate using the remaining screws. Don't over tighten the screw because this could cause the swivel to come off the track, and also the nylon roller.