Window Handle Repair

The window handles may be broken or loose and leave the window open to burglars. The good news is that they're generally repairable.

Take off the plastic caps at the top and bottom of the handle. This is a simple job that shouldn't take longer than five minutes with the screwdriver.

Loose Screws

Over time, a window handle will loosen due to wear and tear or use. If you feel the handle is wobbly, or it is difficult to open it could be because the screws are loose. This is a very easy fix that can be accomplished in just minutes with the help of a screwdriver.

Remove any plastic caps covering the screws on the top and bottom of the handle. They can be removed using either a flathead or a fingernail. Once the caps have been removed, start with the screw on the top and tighten it carefully until it is secure. You don't want to over tighten the screw as it could damage the head. Then, move to the screw at the bottom and tighten it in the same way. After both screws have been tightened, the handle will be stronger and will open more easily.

If you feel your window glass replacement handle is very loose, or if the lock paddle is not able to be put in, it could be time to replace the crank mechanism. You can purchase one via mail order from many double glazing repair (your domain name) hardware specialists and it's likely to be cheaper than replacing the whole handle. Alternatively, you can try tightening the existing crank by opening the window until the crank arm guide bushing is aligned with notch in the track. After carefully pushing down on the handle, remove any trim mounting screws and lift the casement from the window jamb. (Photo 1) You'll need to replace any rusted or bent trim screws. Check the new operator against the old one to ensure they are in the same place, double glazing repair and then install it as illustrated in Photo 5.

Filling holes in wood that are loose prior to tightening them is essential. Filler should be slightly larger than the screwhole to ensure that it doesn't pierce surrounding wood when it's twisted in place.

Broken Spindle

The spindle of your window handle could become worn after a period of time. This may cause the handle to fail or stop opening properly. Fortunately, replacing the spindle is a quick and simple fix that can be accomplished by anyone with some basic tools. It is also essential to check the position of the handle to make sure that it is securely in its place.

It's also recommended to apply a silicone-based lubricant for the spindle and handle after cleaning. This will help it to rotate more smoothly, eliminating any debris or dirt that could hinder its purpose.

One of the most common issues that is common to uPVC windows is the failure of the locking mechanism. This occurs when the spindle isn't moved across the wedge block in a proper manner by the handle. This can be a significant issue as it can prevent your window from opening or shutting. You'll need to replace the handle or lock.

It is essential to determine the length of the spindle before buying a replacement. This will allow you to find the perfect replacement and provides an accurate replacement for your old handle. The measurements are usually located on the bottom of the handles If you can't find them, you can contact us to identify the model by phone.

You can also buy an entire replacement set of handles that have spindles in order to save time and money. These are usually cheaper and can be put in less time.

If your uPVC tilt and turn window remains stuck in the closed position after attempting all of these solutions, it might be the time to speak with a professional. A skilled uPVC expert can inspect the handle for any issues and give you a quote for the repair work.

Our selection of replacement uPVC handle styles includes keys, inline, espags, cockspurs, and cranks. We stock a large selection of both uPVC and aluminium handle designs with a variety of finishes. We can place orders for specific styles if they are not in stock.

Broken Handle

If the uPVC window handle does not open at all, this can be caused by a damaged handle. This is typically due to the handle breaks internally and it is unable to make a purchase on the spindle, and therefore unable to operate the window. This is a common problem with uPVC handles and is fixable easily by removing the handle and replacing it with an entirely new one.

This usually requires the use of a screwdriver and some elbow grease but can be accomplished at home with no professional assistance. The first step is to take the handle from the window. This is done with the screwdriver or other tool that lifts off the plastic cap. This will reveal the top and bottom holding screws that hold the handle base. The top screw should be tightened using the screwdriver until secure. Be careful not to tighten too much it, as this could harm the handle or frame of the window.

After you've made sure that the handle is securely fixed to its base, you can then replace the second holding screw, which must be tightened until firm. Replace the caps made of plastic on both screws, and your aluminium handle should now function just as it should.

A worn-out gear in the cranking mechanism can also cause the uPVC handle to not open. The handle can rotate, but it will not open the window made of uPVC. This could be frustrating and risky to your security. In this instance it is recommended to replace the mechanism for operating.

The process is quite simple and shouldn't take more than just a few minutes. However, if you are not comfortable with this process or would like to hire experts, the staff at Bridgewater Glass are happy to assist you. We have a great deal of experience in the repair and replacement of handles made of uPVC and can ensure that your windows are working and safe. Contact us today to inquire about our services and find out more about how we can help you.

Broken Base

Over time, a window handle can loosen. Sometimes, it could cause the window to sag or open when it is it is opened. This is usually a sign that the mechanism is not being tightened to the frame by one of the screws. It's easy to fix. Simply loosen the screw with a hand screwdriver, and then tighten it. Close the window and move the handle back into position.

Sometimes, handles can break completely from the base section. This happens with both tilt-and-turn and standard handles. It is extremely rare and typically only occurs in high use areas. Luckily, this is also an easy fix and can be fixed by replacing the part.

The handle teeth may also be stripped. This is a common problem in older windows with a crank handle. The teeth, which are typically made of cast iron are prone to being ruined due to excessive use or age. This is a simple repair that can be done with small vice grips or a pair pliers.

In the event that your handle splits away from the base and you need to take off the crank mechanism to access and replace the handle. It can be a bit difficult for novice DIYers to tackle, but it is possible.

First take off the screw that holds the crank operator to the window frame. Then, you can open the window until the guide bushing aligns with the track's notch. Then, using a pair of pliers, push out the window and move the guide bushing off the crank arm.

After you have removed the old handle, check the crank stud to see if the teeth are worn. Then, look over the handle for signs that it's worn. Family Handyman advises that if the splines have worn it is recommended to replace the window crank handle.

Reattach the trim cover and any screws that have rusted to the frame before installing the new window crank handle. Make sure that the holes for mounting screws are in alignment with the holes for mounting on the new handle. then join the base plate with the remaining screws. Do not overtighten the screw, as this could cause the swivel to fall off the track and onto the nylon roller.