Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to auto locksmiths with experience with the right equipment and technical knowledge. They can design and program keys quicker and more efficiently than dealers.

If the key fob stopped locking or unlocking your doors it could be due to a dead battery in the coin. There are other causes why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. If this is the case, you'll need to use the backup starting method that is detailed in the owner's manual for your vehicle.

Another reason why your 208 might not start is because the spark plugs are been damaged. The spark plugs ignite fuel to start the engine. However they have a short time of life. If they aren't used enough they will eventually fail.

Fortunately, there's an easy solution for this problem. The best option is to determine the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts, it's the time to replace it. If the battery has corrosion it is crucial to clean its contacts. This can be done by removing the rubber cover from the two battery terminals, and then using a wirebrush to clean any damaged parts of the battery. Then, you should connect the cables that connect the positive and negative poles.

Water Damage

If your 208 won't start and the battery hasn't been replaced, you must look at the spark plugs. It is possible that they're dirty, causing them to not to spark. The spark plugs can be cleaned in a workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures that only the right key can start the engine. If the chip inside the Peugeot key is damaged, it won't transmit the correct signal to the vehicle.

This is a typical issue that can be caused by water damage. This is particularly prevalent in colder climates, as the vehicle might have been exposed to rain or snow. In this case, you need to contact a trusted locksmith who will have the necessary tools and equipment to change the key's programming. They will also have the latest technology and the machinery needed to create the Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts of the battery may be damaged.

Peugeot replaced the old transponder chips using a new model that utilizes electronic components that are mounted on a circuit board. This new technology works great when it's fresh, but over time the circuit boards begin to wear out and stop functioning correctly.

This could prevent the immobiliser from triggering so that your vehicle won't start. Contact a Peugeot specialist, or a locksmith if this is the situation.

Another issue that is common is when the battery for the key fob gets depleted, which causes the key blade to stop feeding into the lock. A car locksmith will replace the battery, and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob was not working after dropping it on the ground, being exposed to a sudden downpour or accidently washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals to prevent water from getting to the chip inside. The chip can be damaged by water if it is exposed to water for a prolonged period of time. Submerging the key fob into sea water at the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your Peugeot spare key fob isn't working then you'll have to get the module replaced. This can only be done by an expert auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct programming to start the engine. This is the reason that you should only rely on the Peugeot locksmith to design and program an alternative.

Faulty On-Board Computer

The computer on the board of your Peugeot 308 Key Fob Replacement, Foro.Cavifax.Com, is responsible for a variety of the systems in your vehicle, from airbags to power windows. The computer on board will display the code when something goes wrong. This code is stored inside the system and remains there until the issue has been resolved. Most often, this involves replacing the on-board computer.

One of the most frequent reasons for the light coming on is loose or corroded connectors in the airbag sensor. This could be due to wear and tear, aging or exposure to moisture and salt. This issue must be addressed as soon as you can, because an airbag that's malfunctioning could be dangerous in case of an accident.

If your Peugeot is showing a card not detected error, then the battery inside the key fob may be weak or dead. This will stop the key fob sending a signal to disable the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If it doesn't work, the key battery has to be replaced.