Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain, durable and long-lasting. They don't get rotten or rusty like timber and aluminum.

It is crucial to wash and oil UPVC doors and windows regularly. This will save you from unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause serious damage to your home and may even be fatal. You should take the time to ensure that your windows are in good condition.

Single-pane windows are relatively easy to replace and typically fit into frames that were previously in use very easily. If you have double-paned windows that are joined by internal beading, it will be more difficult to remove and replace the old panes. In this instance, it is necessary to purchase plastic spacers to make sure that the new pane fits into the window frame.

Wearing protective eyewear and thick gloves is a must for anyone who plans to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes so that any shards fall on the fabric and not onto the floor, where they could be trampled.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to block drafts and water from entering the property until a professional comes out and fix the window. This also serves as a barrier to prevent any intruders from making their way into your home. If the gap is large, you may be interested in the security door with an integrated window, since it offers the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber sash windows. However, with time, window doctor they can suffer from a variety of problems including sagging. A sagging window in uPVC can cause problems with light, draughts, and even security. It is crucial to act immediately if you notice your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window that is sliding. To do this, you'll need to open the window to get to the frame. You can then unscrew both the hinges on the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, close your window and check for fitting. If you're satisfied with the fit, you can tighten the screws until they remain in place.

If you can't reposition the hinges, you may require replacing the seal. Rubber seals may dry out and lose their elasticity over time, causing them to loosen. If this happens, it's important to replace the seal as quickly as you can to ensure that your uPVC windows are watertight and safe from drafts.

UPVC handles can also become loose. Most often it is due to screws that have become loose over time. However, it can be due to the fact that the handle mechanism has worn out. It's fairly simple to repair a loose uPVC handle. The first step is to close the window and then perform an experiment fit. The joint at the corner of the sash must align with the joint on the casing. If it isn't then you can use the screwdriver to loosen the handle. Then, turn the mechanism to position.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains it's important to take action. Leaks of water from windows can cause structural damage to your home and hinder your ability to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be completed by any skilled DIYer. Depending on the severity of the issue the caulking that was used up may require removal before a new layer of caulk is applied. It is essential to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area more difficult to clean and could reduce the efficiency of your energy.

Make sure that the drainage holes have no debris inside them and that the sill pan has been properly angled to drain away from the window. In more serious situations, you might have to consider replacing the window Doctor.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leakage is coming from between the glass of your double-glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sliding. A uPVC specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open in a breeze, it may be hinges that are at fault. These are easily repaired by any skilled DIYer and can be done within a few minutes.

Like all mechanical parts, hinges can be damaged over time. The process of replacing a hinge on a window is essentially a simple procedure, but it is easier with someone else to assist in holding the frame in place.

It is also important to verify that the uPVC hinges are being opened and closed in the correct direction. This can be done by checking for the arrows on each hinge. This shows which way the window should be opened.

The issue can be caused by opening the window improperly or due to a poor installation at the factory. Sending us a picture via our website will often resolve the problem. We are always happy to provide assistance.

Regular lubrication of hinges is also essential. This can be accomplished by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also stop corrosion and reduce the possibility of sticking. This must be done at a minimum every year. WD40 and other solvent-based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also become unbalanced due to wear, which can cause a gap between the frame and sash. If they're beyond repair, it may be necessary to get them re-aligned. Second, the interlock can also become misaligned. This happens on the hinge's side and may need to be cleaned. In certain instances it is possible to replace these.

These seals are susceptible to wear and tear or get damaged over time, allowing air escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures, and reduce the possibility of draughts.

Lastly, one of the most effective methods to reduce drafts is to use an draught excluder. These are typically made of fabric filled with some type of filler. They can be positioned on the top of your windowsill. They will help stop cold air from entering and keep your home warm and cosy!

With a bit of regular maintenance and repair your windows made of upvc will provide an excellent level of security and insulation for your home. It is crucial to keep in mind that all windows eventually become worn out, and it may be more cost-effective to simply replace them rather than repair them. So, if you are having issues with your upvc windows, it is always recommended to seek assistance from a professional immediately.