Peugeot 208 Key Replacement

It is better to leave the replacement of Peugeot 208 keys to auto locksmiths that have the required equipment and know-how. They can design and program keys quicker and more efficiently than dealers.

A dead coin battery is most likely to be at fault the reason your key-fob stops locking or unlocking doors. However, there are many other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking, and will not allow you to start the engine. In this situation, you will need to choose the alternate method to start that is described in the owner's manual.

The spark plugs can also be worn out. The spark plugs are responsible for igniting the fuel that powers the engine. They have a limited life span. They'll eventually fail if they aren't used frequently enough.

Fortunately, there's an easy solution for this issue. Verify the voltage of your battery using a multimeter. If the voltage is lower than 11,5 volts, then it's time to replace it. It is also necessary to clean the contacts of the battery if it has corrosion. This can be done by removing the rubber cover from the two terminals on the battery and then using a wirebrush to clean any parts of the battery that are corroded. Then, shop you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 won't start and the battery has not gone flat, you should look at the spark plugs. You may find that they're dirty and do not spark. This can be easily corrected by cleaning the spark plugs in an workshop.

Peugeot cars have a transponder key that works with the car's immobiliser system. This ensures that only the correct key can start the engine. If the chip inside the Peugeot key is damaged, then it won't transmit the proper signal to the vehicle.

This is a typical issue that is caused by water damage. This is a common problem in more cold climates where the car is exposed to rain or snow. In this situation, contact a trusted locksmith who has the required tools and equipment to reprogram the key. They will also have all the latest technology and equipment required to make a Peugeot smart key. The process shouldn't take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon-encased transponder chips to an entirely new type of chip that incorporates electronic components in a circuit board. The new system is excellent when it's brand new, but the circuit boards wear out over time and stop working properly.

This can stop the immobiliser from activating so your vehicle won't start. If this is the case it's a good idea to seek out a peugeot boxer key specialist or locksmith.

Another common issue is when the battery of the key fob starts to die, this causes the key blade to stop from entering the lock. A locksmith from your car will replace the battery, and cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob stopped working after dropping it on the ground, being exposed to a sudden rain or accidently washing it the wrong way, it could be due to a defective receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which controls the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals to prevent water from reaching the chip inside. However prolonged exposure to water can penetrate these seals and damage the chip. The high salt content of the ocean or pool could cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob stops working it is necessary to have the module replaced. This can only be done by a Peugeot specialist or a professional auto locksmith. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct coding for the start of the engine. This is why it is imperative that you should only rely on an authorized Peugeot locksmith to create and program an alternative.

Computer on board is not working properly

The on-board computer in your peugeot key replacement near me is responsible many features in your car, including power windows and airbags. When something goes wrong with these systems, they will usually display a code that indicates the issue. This code will be stored in the system until the problem is fixed. This will often require the on-board computers to be replaced.

The most frequent cause for the warning light for airbags to illuminate is corrosion or loose connections within the sensor. This can be caused by wear and tear, aging, exposure to salt and moisture. It is imperative to have this issue resolved as soon as possible, since the airbag malfunctioning could be dangerous in the event of an accident.

If your Peugeot is showing a card that is not being detected error, the battery in the key fob may be dead or weak. This will stop the key fob from sending a signal to disarm the immobilizer on your vehicle. Test this by pressing the unlock key on the key fob and then trying to start your vehicle. If this doesn't work then the battery in the key will need replacing.