How to Replace a Kia Sportage Replacement Key

For a variety of kia Picanto spare Key (http://lookingfor.kr/) models the key comes with the keyless entry system that is built into the key. This key is similar to the remote control and can be exchanged by a Kia dealer.

Key fobs may stop working for a variety of reasons, such as an empty coin battery worn buttons, water damage, signal interference and a damaged receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage once more.

How do you replace the remote key or smart key?

No matter if your Kia is equipped with an intelligent key, remote key push-to-start key, or regular metal non-transponder key, the battery in these keys will eventually require replacement. This is especially true if the car displays a message telling that the smart key or remote has a low battery.

It's a fairly simple procedure. To replace the battery on the key fob take the mechanical key from the slit on the back of the key fob. You then need to lift the cover. A small screw will be located inside the key fob, which holds the battery in the correct position. Remove the old battery by unwinding the screw with a small screwdriver. Insert the new battery and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. It's okay in case the doors lock and unlock as you expect. You can now use the hands-free feature to lock and unlock your kia replacement key fob whenever your fingers feel cold or you have to complete errands in Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of metal) are not required for programming. If you're looking to reprogramme your key, you'll have to write down the key code's number on the key code tag.

How do I replace the battery?

If the Kia key fob does not respond to pressing the lock or unlock button, it's likely that the battery is not fully charged. A weak battery could cause other issues, like the check engine light coming on or the engine not cranking properly. Fortunately replacing the key fob battery is a relatively simple DIY project that requires just a few basic tools.

Make sure to shut off your vehicle and shut all doors before you begin. Find the small metal or a plastic piece at the bottom of the key fob. Press it until the key comes out. You can then insert this key into the handle of the door for the driver to unlock your car.

To replace the battery in the key fob, take off the cover that covers the rear. Use a plastic pry tool to loosen the latch that holds the black negative cable. Take the old battery out, and then orient the replacement battery to ensure that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

After installing the new battery and turning the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob once more to ensure it's functioning properly.

How to replace the smart key?

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart key comes with tiny mechanical key blade that is hidden inside, while the standard fob does not. Both key fobs have a battery that will eventually require replacement. Fortunately, it's an easy task that will take about two minutes.

Make sure you turn off your Kia, and be on a flat, well-lit surface before you begin. Keep in mind that the fob is made up of tiny parts that could be thrown off if you're not careful.

The first step is to locate the small release button that is located on the lower backside of the fob. It will be a circular button or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened, you can simply take out the old battery and replace it. The new battery is a the CR-2032, and it can be bought through the internet or at a local auto parts store. After you're done, your key fob should permit you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace a mechanical key

The kia picanto key replacement keyfob is a great convenience that lets us lock or unlock our car by simply pressing a button. However, like all devices it will encounter issues at times. There are solutions to address these issues and keep your key fobs working for an extended period of time.

A dead or drained battery is one of the most common issues. This can cause the fob to stop working entirely or even to stop working intermittently. If this is what you are experiencing, replace the battery with a new one.

If this isn't enough to solve the issue, you can use an ordinary screwdriver with a flat head to wedge the fob's casing made of plastic open. Be careful not to harm any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a brand new one.

After the new battery has been put in, shut and open the doors with the mechanical key (every kia fob has an emergency mechanical key that will fit in the slot). Test the key fob to check that it's functioning correctly. If the fob not working, contact an expert locksmith or dealer to help solve the issue. To avoid a lockout in the future ensure you have an emergency key that can work in all of the trunk and door cylinders.