How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with an electronic keyless entry system built into. The key is usually akin to an remote control, and is able to be replaced with a brand new one from a Kia dealer or a locksmith.

Key fobs can fail to function due to a number of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some helpful tips to help you get your Kia key fob that is a replacement kia key for the sportage again.

How to replace a remote key or a smartkey?

It doesn't matter if your Kia is equipped with an intelligent key, remote key, push to start key, or regular metal non-transponder key the battery in these keys will eventually require replacing. This is especially true if your car displays a message that indicates the smart or remote keys aren't powered.

Luckily, it's an easy procedure. To replace the key fob battery remove the mechanical key from the slit in the back of the key fob. You then need to break the cover. A small screw is in the key fob to keep the battery in the correct position. By using a small screwdriver unscrew the screw and pull out the old battery. Install the new battery and then close the opening on the key fob.

Once the key fob has a fresh battery and you've tested it, press the lock and unlock buttons. It's good if the doors lock and unlock as expected. You can now use your Kia's hands-free lock/unlock feature whenever your fingers feel cold or you have to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a programming machine that is only available to the locksmith for cars or dealer. Other keys (non transponder metal keys) don't require programming. If you want to change the programming of your key, you'll need to record the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's a sign that the battery is insufficient. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately, replacing the key fob battery is a relatively simple DIY task that requires only a few basic tools.

Make sure that you shut off your vehicle and close all doors before you begin. Locate the small metal or plastic piece on the bottom of your key fob, and play with it until a metallic key slips out. The key can be inserted into the driver door handle to unlock your car.

To replace the battery inside the key fob, remove the rear cover. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery, and then align the new battery to ensure that the "+" positive side faces you and the "-" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the metal contacts.

After the new battery has been installed, turn the key fob off and then on in the ignition repeatedly until the door locks cycle. Then you can test your Kia key fob and see if it is working properly again.

How to replace the smart key

Depending on the model of your kia sportage key Sportage, you may have a standard key fob or a smart key. The difference is that the smart key is equipped with a small mechanical key blade tucked inside it, while the standard key fob does not. Both kinds of key fobs contain a battery inside them that eventually will need to be replaced. This is a simple procedure that takes less than two minutes.

Before you start it is important to make sure that you are on a level surface with sufficient lighting and that your Kia is turned off. Also, remember that there are tiny components inside the fob that could fall out if not careful.

The small release button is located on the lower backside. It will be either an oval silver button or a rectangular slot. When you press it the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been opened, remove the battery. The new battery is a CR-2032, and can be purchased on the internet or at your local auto parts store. After installation it should be possible to lock and unlock your car using your key fob - even if your engine isn't running!

How do I replace a mechanical key

The Kia keyfob can be a fantastic convenience that lets us lock or unlock our car by pressing one button. Like any other device like a key fob, the Kia might have issues. Luckily, there are steps to take to fix these issues and ensure that our key fobs are in good working condition in the long run.

One of the most frequently encountered issues is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the issue, replace the battery with an entirely new battery.

If this doesn't fix the issue then try using a normal flathead screwdriver and wedge it into the fob's plastic casing. Be sure not to damage any internal components or scratch the plastic. Once open, carefully remove the battery you have been using and replace it with a new one.

When the new battery is in, close and then open the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob and check that it's functioning correctly. Contact a dealer locksmith to resolve the problem in the event that the key fob is not working. To avoid future lockouts, make sure you get an emergency key that will work on all door and trunk cylinders.