How to Replace a Kia Sportage Replacement Key

The key of many Kia Replacement Key Fob models comes with an entry system that is keyless into. This key typically resembles a remote control and can be replaced with a brand new one from an Kia dealer or a locksmith.

Key fobs can stop working due to various reasons, such as an empty coin battery worn buttons signals, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions on how to get your Kia Sportage replacement key to function again.

How do you replace a remote key or smartkey

Whether your Kia comes with an intelligent key, remote key push-to-start key, or regular metal non-transponder key the battery in these keys will eventually need replacement. This is particularly in the event that your car displays a message telling that the remote or smart key is not powered by the battery.

Fortunately, it's quite simple to do. To replace the battery of the key fob take the mechanical key from the slit on the back of the key fob. You then need to break the cover. Inside the key fob there will be tiny screws that hold the battery in its place. Take out the old battery by removing the screw using the help of a small screwdriver. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors unlock and lock as expected, then you're set! You can now take advantage of Kia's hands-free lock/unlock function whenever your fingers feel cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key requires to be reprogrammed, then you will need to know the key code number written on the tag of the key code and save it in a safe location.

How do you replace a dead battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a sign that the battery should be replaced. A low battery may cause other issues, like the check engine light appearing or the engine not cranking correctly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires just the most basic tools.

Make sure you turn off your vehicle and close all doors prior to starting. Find the small metal or plastic piece at the bottom of your key fob and move it until a metal key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and then orient the new one in a way that the "+" positive side is facing you, while the "negative" negative side is facing towards the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

Once the new battery is installed after which you turn the key fob off and on in the ignition several times until the door locks cycle. You can then test the Kia's Key fob once more to ensure it's working properly.

How do I replace a smart keys

You may have either a standard keyfob, or a Smart Key depending on the model of Kia Sportage. The difference is that the smart fob has the small blade of a key in it, whereas the standard fob isn't equipped with. Both types of key fobs have a battery inside them which eventually needs to be replaced. This is an easy process that takes just two minutes.

Be sure to switch off your Kia and sit on a level well-lit and well-lit area before you begin. Keep in mind that the fob has small pieces that could be thrown off should you not be careful.

The release button for the small size is located on the lower backside. It can be an oval silver button or a rectangular slot. Once you press this, the mechanical key blade will appear and you will be able to open the key fob.

Once you have the key fob open and you are able to remove the old battery, and replace it. The new battery is C2032, and can be bought on the internet or at your local auto parts store. Once you're done, your key fob should allow you to lock or unlock and start your vehicle even if it's not running.

How do you replace the mechanical key?

The Kia key fob is a wonderful feature that lets us lock and unlock our car with the click of one button. But like any device, it can have problems at times. There are solutions to fix these problems and keep your key fobs running for many years.

A low or dead battery is among the most frequent problems. This could cause the fob to stop working entirely or even to stop working intermittently. If this happens you should replace the battery with a fresh new one.

If this doesn't solve the problem you can try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery that was removed and replace it with a new one.

After the new battery has been put installed, close and unlock the doors with the mechanical key (every kia picanto car key replacement fob has an emergency mechanical key that will fit in the slot). Test the key fob to verify that it's working properly. Contact a dealer or locksmith to fix the issue if the fob is still not working. To avoid locking outs in the future, ensure that you have an emergency key that will work on all trunk and door cylinders.