UPVC Window Handle Replacement

Replacing a broken window handle is a easy task and, with the right tools, it can be accomplished quite quickly. It is important to know the type of handle you have and its spindle size before you purchase a replacement double glazed window.

Older uPVC windows feature cockspur handles for windows. They have an extension spur that can secure a wedge-shaped cockspur striker plate. These can be right-handed or left-handed and must be matched when replacing.

What kind of lock or handle do I have?

There are a variety of window handles made from upvc and locks, each having their particular advantages and uses. The type of handle that you own will determine whether or not the locking mechanism you have is effective and if it's easy to open the windows. Over time, and with regular use the handles made of upvc on your windows can become damaged and worn out. This makes them less secure and effective. In some cases they could even be completely removed. If you find that your window handles have fallen off, it is important to repair them as quickly as possible. This will help prevent potential break-ins and ensure your home is secure.

It is a good thing that replacing your window handles made of upvc is a relatively simple task that is achievable by nearly anyone. You will need a few basic tools, but with proper knowledge, it's simple and should take only a couple of minutes. To get started you must determine the type of lock and handle that you have on your upvc window to help you to find the ideal replacement.

Inline Espagnolette Handles

They are typically found on the outside of the window. They are flat and feature a latch which engages the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the middle of the handle into the window frame to control the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the frame and are not as secure as other kinds of window handles.

Handles that turn and tilt

In contrast to other upvc handles that are tilt and turn, Glass Replacement windows these handles can be rotated to open the window, and turned inwards to allow for ventilation. They feature a 7mm spindle on the back and are available in left and right-handed versions.

It is essential to know the spindle size when buying new upvc handles. Not all are exactly the same size. Drop something in the middle of the hole to test the length. This is the maximum spindle length that will be suitable for your window.

What is the spindle?

uPVC window handles operate similar to doors, by turning the handle to activate a latch inside the frame. The latch opens the window, so that it can be closed and opened. But, at times, these handles can become damaged, particularly when they are used frequently or exposed to harsh weather conditions. It is possible to replace the handles on your uPVC window if they're not operating correctly.

There are several different types of uPVC handles available including Espag, Cockspur and Spaded handles. These handles are designed in a variety of ways to fit into uPVC frames. Each handle type utilizes an individual spindle to lock the window mechanism. It is important to identify the kind of handle that is installed on your uPVC windows so that you can replace it with a suitable one.

You can determine the type of uPVC handle you are using by inspecting the base of your handle. A snap-in covers should be over the screw that holds the base of the handle in place. Take it off and you should be able see the second screw at the opposite end of the base section of the handle. After both screws have been removed and you are able to pull the handle from the uPVC.

After you have removed the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You'll need to purchase a Glass Replacement Windows with the same length as the original handle and the locking device.

The spindle wears out and is unable to operate the locking mechanism. This could be due to corrosion, damage due to frequent use, or a loosening locking mechanism. If this occurs, it will be necessary to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I get rid of the old handle?

In the course of time and daily usage, window handles could become damaged or broken, and if this happens, it is important to repair them as quickly as possible to ensure the safety of your home. It is easy to replace a worn or damaged handle. The job can be completed in less than a minute without the need for any special tools.

The first step to remove the old handle is to remove the screw located at the top of the handle base. Once this is removed the handle can be pulled away from the base section. A second screw is located at the bottom of the handle. This too can be removed. After both screws are removed, the handle can be completely detached from the base section of the window.

After removing the old handle, align the fixing holes of the new handle with the holes that are already in the window frame. If there is a sticker or cap on the new handle, remove it if needed and screw the handle into place. Once the handle is set, it is important to test that it is working by turning the handle and ensuring that the lock mechanism activates.

Espag handles come with a spindle that protrudes from the handle and slots into a multipoint locking mechanism inside the frame of the window. Cadenza windows come with a blade with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that is able to hook over the frame's outer or the transom bar cross member in the window.

Once you have the new handle in place, slide the spindle inside the lock inside the window and then tighten it down. Once the handle is securely fixated, replace the'snap in' cover and the screw cap (if necessary). Now that the handle is ready for use, simply open and close the window a few times to make sure that it functions properly and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult, and the process is actually very simple. All you need is an screwdriver and a bit of patience. First, make sure the handle that you are replacing is unlocked. Then, remove any visible screws. You can also replace them with screw caps. After removing the handle and you are ready to take a note of the length of the spindle that protrudes from the back of the handle. This is important as it will determine what type of handle you need to purchase.

Espagnolette handles are the most commonly used kind of handle that is used on uPVC windows. The spindle passes through the handle to control the locking mechanism in the window frame. The handle opens the latch and allows the window to open. In regular use and over time, handles made of espagnolette can become damaged.

Cadenza handles are a type of uPVC handle that is commonly employed with tilt and turn windows. They have a protruding blade that operates a multipoint locking mechanism within the window. They are more secure than an espagnolette handle as they can only open from the inside. They can be replaced using the same method that you would for espagnolette handles however, ensure that the new handle is angled, not flat.

After you have chosen the correct handle, simply align the new handle with the existing screw holes prior to screwing it in place. You should then put the screws back on and test that the new handle is working properly. This is done by moving the handle from locked to the unlocked position and then back to the locked position a few times. If you have any issues, it could be worth contacting a specialist to see if they are able to assist you in solving the issue. They can offer advice on how to solve the issue in a timely and effective way.