Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain, durable and long-lasting. They are not susceptible to rot or rust like aluminum or timber.

It is crucial to wash and oil UPVC doors and windows on a regular basis. This will reduce costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. You should take the time to ensure that your windows are in good working order.

Single-pane windows are fairly simple to replace and generally fit into old frames very easily. However when you have double pane windows that are held in place by internal beading it will be more difficult to get rid of the panes that are in place and replace them with new ones. In this situation you'll need to source some plastic spacers that will assist the new pane to fit perfectly into the frame of the window.

Wearing eye protection and thick gloves is essential if you plan to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes, so that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled.

It's a good idea to cover the gap with tape after the glass has been removed. This will stop water and drafts from entering your property until a professional comes out to repair the window. It also acts as a barrier, preventing any intruders from getting access to your home. If the distance between the door and the window is significant, you may need to consider security screens that has a window. This will give you the best of both.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash windows. In time, they could be affected by a variety of issues that include sliding. A window that is sagging can cause problems with light, draughts or even security. If you notice that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from worsening.

To fix a sagging window you can try repositioning the hinges. To accomplish this, you'll have to open the window so that you can access the frame. Then, you can remove the top and bottom hinges using a screwdriver, and then adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you have repositioned your hinges. If you're happy with the fit, double glazed Window repairs near me tighten the screws to ensure that they stay in position.

If you can't reposition the hinges, you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, leading them to loose their elasticity. If this happens, it's important to replace the seal as fast as possible so that your uPVC windows are watertight and safe from drafts.

uPVC handles may also loosen up. This is usually due to screws that have become undone over time, but it could also be due to the handle mechanism wears out. It's a good thing that it's simple to repair the loose uPVC window handle yourself. First, you'll need close the window and then perform an experiment fit. The corners of the sash need to be aligned with the casing joint. If it doesn't then you can use a screwdriver to loosen the handle, and then return the mechanism to its original the position it was in.

3. Water Leaks

It is important to act if you awake each day to find mouldy walls and floors that are wet. The leaks of water through windows could cause structural damage to your home, and hinder your ability to control the temperature of your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame has been damaged or is missing.

It is a fairly easy fix that can be completed by any DIY expert. Depending on the severity of the problem the caulking used previously might need to be removed before a new layer is applied. When it is time to uPVC repair, it is important to avoid 'over-caulking'. This will make your window more difficult to clean and reduce its energy efficiency.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled correctly so that it drains away from the window. In more serious instances, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the house.

It is also important to note that if the leakage originates from the glass of your Double Glazed Window Repairs Near Me-glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and blow open in a breeze, it may be hinges that are at fault. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical part, hinges can wear out over time. It's easy to change the hinges on a window, but it's easier if someone else helps you hold the frame.

Make sure that the uPVC hinges are closed and open in the proper direction. Look for the arrows that are on each hinge to determine which way the window should be opened.

The problem can be caused due to opening the window in the wrong way or by a poor installation at the factory. Sending us a photo via our website will often solve the issue. We are happy to give suggestions.

Regularly lubricating the hinges is also necessary. Applying an engineering lubricant that is light to the hinges is an ideal way to do this. We recommend using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can help the window operate and close more smoothly. It can also prevent corrosion and reduce the possibility of sticking. This should be done at least once a year. WD40 or other solvent-based lubricants are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by different factors. The hinges may also become disaligned as a result of wear, which can cause gaps where the sash meets frame. If they are beyond repair, it could be required to realign them. The interlock, which is on the hinge side of the window, can also be misaligned, and again it's feasible to give them a thorough clean, however in certain cases, it may be necessary to have them replaced.

The next most common reason for draughts is window repair seals. They are prone to wear or damaged over time, and will allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with glass that is low-emissivity, this will help to regulate indoor temperatures and again will lessen the possibility of draughts.

Another, and most effective methods to reduce draughts is by using a draught excluder. These are typically fabric tubes that are filled with some kind of filler. They can be placed on the windowsill on top. These will help to keep cold air out and keep your home warm and cosy!

With a little maintenance and repair your windows made of upvc will continue to provide a great level of security and insulation for your home. It is crucial to keep in mind that all windows will eventually get worn out and it could be more cost-effective to simply replace them rather than repair them. So, if you're having issues with your upvc windows, it's recommended to seek help from a professional as soon as you can.