Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths with the right equipment and technical knowledge. They will be able to make and program new keys faster than a dealership would and at a cheaper cost.

If your key fob has stopped locking or unlocking your doors it is likely due to a dead battery in the coin. But, there are other possibilities that the key is malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, as well as hindering it from starting the engine. If this is the scenario, you'll need utilize the backup starting method which is explained in the owner's manual of your vehicle.

The spark plugs may also be worn out. The spark plugs are responsible for igniting the fuel that powers the engine. They only last for a certain amount of time. If they are not used enough, they will eventually fail.

There is an easy solution to this issue. Check the voltage of your battery using a multimeter. If it is below 11.5 Volts it is time to replace it. If the battery has corrosion it is essential to clean its contacts. This can be done by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any corroded parts of the battery. Then, reconnect the cables to the positive and negative poles.

Water Damage

If your 208 won't turn on and the battery isn't running, then make sure that the spark plugs are working. You might find that they are simply too dirty and they don't spark. The spark plugs can be cleaned in a workshop.

Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This guarantees that only the right key can start the engine. If the chip inside the Peugeot key is damaged, then it won't send the proper signal to the vehicle.

Water damage is a typical cause of this problem. This is a common issue in areas with colder temperatures where the vehicle is exposed to snow or rain. If this is the case, you should call a reputable auto locksmith who will have all the equipment and tools needed to change the key's programming. They also have the latest technological know-how and machinery required to create the Peugeot 208 smart key. The process shouldn't take more than 15 minutes.

Faulty battery contacts

Peugeot replaced the transponder chips by introducing a new version that makes use of electronic components that are mounted on a circuit board. The new system is effective when it's new, but over time the circuit boards start to wear out and stop functioning correctly.

This can prevent the immobiliser chip activating and causing your car to not start. Contact an Peugeot specialist or a locksmith, if this is the situation.

Another issue that is common is when the battery for the key fob starts to die, this causes the key blade to stop from entering the lock. A locksmith in your car can replace the battery and cut a fresh blade for you, it's typically a quick fix.

Faulty Receiver Module

It could be that the receiver module has a problem If your Peugeot key fob isn't working after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for transmitting radio frequency signals to the onboard computer which controls the centralized locking system of your Peugeot vehicle.

The rubber seals on the key fob stop water from getting to the electronic chip. Water can damage the chip when exposed to water for a long period of. The high salt content in the pool or ocean water could cause damage to the key fob when it is submerged.

If your Peugeot spare key fob stops working, you'll need to have the module replaced. This is only completed by an experienced auto locksmith or Peugeot specialist. Like other automobiles, Peugeot keys are protected by an immobilizer that is unique and requires the correct code to start the engine. This is why you should choose a reputable Peugeot locksmith to handle the task of designing and programming an appropriate replacement.

Computers with faulty on-board computers

The computer on board of your Peugeot is responsible for many of the functions in your car including airbags and power windows. If something is wrong with these systems, it will usually display a code that indicates the issue. This code is saved in the system and will stay there until the issue is resolved. Usually, shop this will mean replacing the onboard computer.

One of the most common causes of the airbag light coming on is loose or corroded connections within the airbag sensor. This could be due to wear and tear, aging, or exposure to moisture and salt. This issue must be taken care of as soon as you can, since an airbag malfunctioning could pose danger in the event of an accident.

If you encounter a card not found error on your Peugeot, the key battery inside the key fob could be weak or dead. This will stop the key fob sending a signal to disable the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob and then attempting to start your car. If this fails, the key battery must be replaced.