UPVC Window Handle Replacement

It is easy to repair a broken window handle using the appropriate tools. It's important to know the type of handle you have and the spindle's size before you purchase the replacement.

Older uPVC window handles have a spur that protrudes and locks on the cockspur wedge striker. They can be right-handed or left-handed and should be compatible when replaced.

What type of lock and handle do I have?

There are many different types of upvc window handles and UPVC Window Handle Replacement locks, each with its particular advantages and uses. The type of handle that you own will determine if the locking mechanism you have is effective and if it's easy to open the windows. With time and regular use, window handles made of upvc are prone to wear or damage. out, making them less secure and effective. In some cases, they may even disappear completely. It is important to repair your upvc window handles immediately if you begin to notice they are falling off. This will help to avoid burglaries and ensure your home is secure.

Luckily, replacing your window handles made of plastic is a simple task that can be done by almost everyone. With just a few tools and the right information, this is a simple procedure that should take no more than a couple minutes. To begin you'll need to identify the type of lock and handle that you have on your window, which will help you identify the best replacement.

Inline Espagnolette Handles

They are the most popular kind of upvc handle and are usually located on the side of your window. They have a flat design and feature a latch that connects to the locking mechanism on the window handles replacement frame when turned. Inline upvc handles also come with a spindle that goes through the center of the handle, and into the frame of the window to operate the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and have an distinctive hook-shaped design. Cockspur handles are attached to the frame of the window with only one screw and are less secure than other kinds of window handle.

Handles that tilt and turn

In contrast to other handles made of upvc that are tilt and turn, these handles can be turned to open the windows and the handle can be tilted to the side to let air flow in. In general, they feature a 7mm spindle on the side of the handle. They are available in left and UPVC Window Handle Replacement right handed versions.

When purchasing replacement handles made of upvc it is essential to verify the length of the spindle as not all are the same size. Drop something into the middle of the hole to measure the length. This is the maximum spindle size that will fit your windows.

What is the spindle?

uPVC window handles function in a similar way like doors, turning the handle to open an internal latch within the frame. The window then opens and closed. However, in some cases, handles can be damaged, especially if they are regularly used or exposed to extreme weather conditions. You may need to replace the handles on your uPVC window if they are not able to operate it correctly.

There are a variety of uPVC handles that are available, comprising Espag, Cockspur and Spaded handles. These handles are designed in a variety ways to fit into uPVC frames. Each handle type uses an entirely different spindle for locking the window mechanism. It is crucial to know the type of handle you have installed on your uPVC windows so that you can replace it with the correct one.

You can check what type of uPVC handle you are using by taking a look at the base of the handle. A snap-in covers should be over the screw that holds the base of the handle in position. Remove this and then you should be able see the second screw at the opposite end of the base of the handle. After both screws are removed you should be in a position to pull the handle away from the uPVC window.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Take careful note of the length of the spindle since you will need to ensure that you purchase a replacement that has the same length as the original handle and locking mechanism.

The spindle wears out and is unable to operate the locking mechanism. This can be due to damage caused by constant use or loosening of the locking mechanism, or even rust over time. If this occurs, it is necessary to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I get rid of my old handle?

Window handles can become damaged or broken over time. It is important to repair them as quickly a possible to ensure your security. Fortunately, replacing a damaged or worn handle is a relatively easy task that can be completed in just over one minute and doesn't require any specialist tools.

To remove the old handle, you first need to remove the screw at the bottom of the handle. Once this is removed the handle can be pulled away from the base section. There will be another screw located at the bottom of the handle's base, and this can be removed too. Once both of these screws are removed the handle can be removed from the base section of the window.

After the handle has been removed, grab the new handle and line up the fixing holes with the holes currently in the window frame. There may be a tiny sticker or caps on the new handle, so remove these if necessary and then put the handle in the frame. It is essential to ensure that the handle is working after it is put in place. Turn the handle around and ensure that the lock mechanism is in place.

Espag handles feature a spindle which protrudes from the handle and slots into the multipoint locking mechanism that is on the frame of the window. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hook over the frame that surrounds the window or the transom crossmember of the bar.

Once you have the new handle in place, insert the spindle inside the lock in the window and then tighten it down. When the handle is fixed and secured, replace the snap-in cover and the screw cap (if necessary). When the handle is ready for use, you can open and close the window a couple of times to ensure it works correctly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The process is very simple. All you need is a screwdriver and a little bit of patience. The first step is to ensure that the old handle is in the unlocked position and then take out any screws that are visible, you can also replace them with screw caps if required. Once the handle is removed it is necessary to take an outline of the length of the spindle which protrudes from the back of the handle. This is important as it will determine the kind of handle that you will require to purchase.

Espagnolette handles are the most popular type of handle used on uPVC windows. The spindle is inserted into the handle to activate the locking mechanism in the frame of the window. When the handle is turned it releases the latch on the window, allowing it to open. During regular use and time, handles for espagnolette may be damaged.

Cadenza handles are a different kind of uPVC window handle, which is typically used on tilt and turn windows. They have an elongated blade that functions as a multipoint locking mechanism within the window. They are generally more secure than espagnolette handles as they are only accessible from the inside. They can be replaced using the same procedure as you would do for handles made of espagnolette however, make sure that the new handle is not angled and flat.

Once you have selected the correct handle, simply align the new handle to existing screw holes prior to screwing it in place. After that, you can put the screws on and test your new handle. This is done by shifting the handle from the locked to the unlocked position and the reverse direction a few times. It is possible to contact an expert to see whether you can solve any problems. They can offer advice on how to solve the issue in a timely and efficient manner.