Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat keys replacement (click through the up coming document) 500 number is a convenient way to unlock the doors and get started the car. However, there are many reasons why the key fob might stop functioning. This could be due to a dead battery and water damage, as well as receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 key fob Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob not working. Modern key fobs have a limited operating range, and should be within just a few feet of the car to operate. If you are not within your vehicle, and you press the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

After you've replaced the coin cell battery you can test it by standing in front of your Fiat 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switches.

If your key fob does not work after replacing the battery, there may be water damage that has prevented it from communicating with the module in your vehicle. Water damage can occur in a variety of ways, ranging from a light splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If that doesn't work your fob is likely to need to be reprogrammed by a professional locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a washer. Saltwater is particularly dangerous to the fob's circuit board which causes it to short out and eventually end up dying. Getting the fob wet is not an ideal choice but if you accidentally drop it into a glass of water or fail to remove it from your pants pocket prior to running the washer do not give up hope.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Next test the fob to test if it works. If the fob doesn't work, it may have to be reset. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your car It will most likely need to be replaced completely. A professional locksmith in the automotive industry can do this job. The locksmith will have to cut the key to match the ignition of your car. The locksmith will also have to reprogram your fob into the car's system. This is a quick and cost-effective process which can be completed in the same day.

Receiver Module Issues

The 500 key fob could not function because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your car, it won't respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If your fob doesn't work after replacing the battery inside the coin, which is also known as a "button", "watch" or "button" or "button", it could be due to an issue with the internal circuit board. In the majority of cases, reprogramming your fob can resolve the problem. You can find instructions on how to do this on the majority of vehicles by searching YouTube or looking through the owner's manual.

It may be necessary to replace the metal clips that hold the coin batteries in the correct position. If they lose tension it could prevent the coin battery from being properly seated and can result in the malfunction of your remote.

In rare instances, the fob may become disconnected from your vehicle because of software or hardware issues. This could be a huge issue, but you are able to often fix this by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain situations it may be necessary to install the software again in your body control module, too.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive signals due to interference. This may happen if the keyfob's location is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob may not function because of a weak connection with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It converts the signals into electronic commands that are then read by the vehicle.

Luckily, there is an easy method to reset every single system on board in your 500 keys, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computers. This can help the key fob to function again. If the issue continues, you should consult an expert certified technician. They will be able diagnose the root of any issues.