How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an entry system that is keyless into. The key can be compared to a remote control and can be changed with a brand new one from an Kia dealer or a locksmith.

Key fobs can fail to function due to a number of reasons, such as the battery being dead, worn-out buttons signal interference or water damage. Here are some tips to assist you in getting your Kia key fob that is a replacement for the sportage again.

How to replace the remote key or smartkey?

The battery inside your Kia's smart key will eventually require to be replaced, regardless of whether it's a remote that starts with a push button or a regular key that does not contain transponder. This is especially true if the car displays a message that the remote or smart key has a low battery.

This is a relatively simple procedure. To replace the battery of the key fob take out the mechanical key from the slit in the back of the key fob. Then lift the cover. Inside the key fob will be an incredibly small screw that holds the battery in place. Take out the old battery by detaching the screw using the help of a small screwdriver. Install the new battery and then close the cut on the key fob.

When the key fob is equipped with new batteries check it by pressing the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to complete errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non transponder metal keys) don't require programming. If your key requires to be programmed again, you will need to know the key code number that is stamped on the tag of the key code and record it in a safe location.

How to replace a battery

If the Kia key fob is unable to respond to pressing the lock/unlock button, it is likely that the battery is insufficient. A battery that is not functioning properly can cause other issues, like the check engine light appearing or the engine not cranking properly. It is relatively easy to replace the key fob batteries using just some tools.

Be sure to turn off your vehicle and close the doors before you begin. Find the small metal or plastic piece that is located at the bottom of the key fob. Jiggle it until the key comes out. Then, you can insert this key into the handle of the door for the driver to unlock your car.

To replace the key fob's battery, take off the rear cover and use a plier bar tool to loosen the latch that holds the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or bending the contacts on the metal.

Once the new battery has been installed, turn the key fob off and on in the ignition several times until the door locks. Then, you can test your kia picanto key fob key fob to see if it is working properly again.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard key fob does not. Both kinds of key fobs contain batteries which eventually needs to be replaced. Luckily, this is a fairly simple process that takes only two minutes.

Be sure to switch off your Kia and stand on a flat well-lit and well-lit area before you begin. Keep in mind that there are tiny parts inside the fob that could be snagged if not careful.

The first step is to find the small release button that is located on the lower backside of the fob. It will be either a circular silver button or a rectangular slot. After pressing this button mechanical key blade, it will appear and you will be able to open the key fob.

Once the key fob is open, remove the battery. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. After you've finished with the battery, you should be able to lock, unlock and start your vehicle using your key fob - even if your engine isn't running!

How do you replace a mechanical key

The Kia keyfob can be a fantastic convenience, allowing us to lock or unlock our car by pressing the button. As with all devices that is used, the Kia key fob may have issues. Luckily, there are steps that can be taken to resolve these issues and ensure that our key fobs are in good working condition for the long term.

A dead or drained battery is among the most common problems. This could cause the fob to cease working or stop working at times. If this is the case then try replacing the battery with a fresh new one.

If this doesn't fix the problem, try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new one.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure that it's working correctly. If the fob isn't functioning, contact a locksmith or dealer to help resolve the problem. To avoid lockouts in the future, ensure you have an emergency key that will work on all door and trunk cylinders.