UPVC Window Repairs

Upvc windows are able to reduce heating costs and are energy efficient. As they age, however, problems may develop that need to be addressed. This could be due to damaged hinges, handles or locks.

Wooden window repairs can be relatively straightforward for DIY enthusiasts to complete themselves. It can also be much less expensive than a brand new replacement window doctor.

Cracks

Cracks and breaks can pose a serious problem. If windows are not properly repaired, they can result in water intrusion, less effective barriers to cold weather, and even structural damage. It is important to find an experienced local builder or repair service who specializes in fixing uPVC frames and can demonstrate the skills, experience and tools required to deliver the best results. This will ensure that the crack is fixed before it gets worse and you don't have to replace your window glass or unit.

Small cracks in glass can be fixed with a range of home-based solutions. Superglue and masking tape are two of the most popular products to hold cracked glass in place for a short time. For cracks that are more extensive the tape may have to extend past the crack on both sides to achieve the optimal results.

You can also make use of two-part epoxy for repairing broken or cracked glasses. This is available from most hardware stores and can be purchased for around $10. Make sure your work area is properly prepared prior to mixing the epoxy. Also, ensure that you have all the tools necessary for the job.

If you notice that your lower or upper sash isn't lifting it could be because the cords connected to the sashweights are damaged. This is an easy fix that can be accomplished with a ladder and flathead screwdriver. A damaged dripcap can be repaired at home. Rot-free drip caps are available at most home centers and can be secured with nails and caulked into place with ease. Verify that the glass in double or triple-paned window is not damaged. The reason for this is that the gasses in the space between the windows are responsible for enhancing the energy efficiency of the window. They should not be allowed to escape.

Water Leaks

If your uPVC windows are leaking, it could cause damage to the interior of your house and lead to expensive repairs. Water leaks can also damage the structure of your house and lead to the growth of mold. It is crucial to address any issues caused by leaky windows immediately to prevent damage.

A damaged sealant around window frames is a typical cause of leaks. The use of silicone caulking can improve the condition of the seal back to its normal condition and stop water leakage. It's also important to check for gaps and cracks around the frame, as well as in the stone or brick walls that surround your windows.

Another reason that can cause leaks in windows is the drainage hole is blocked or a defective flashing. Make sure that the drainage holes haven't been blocked or blocked, particularly after heavy rain. Also, you should look at the flashing around your window to ensure it is well-sealed.

Finally, it's essential to ensure that your drip cap isn't broken or rotten. A rotten drip cap or one that's not there will allow water from above to enter your window and cause structural damage. Replacing drip caps isn't an arduous task and is usually a straightforward process of buying an entirely new one and nailing it into place.

A professional can also examine your windows for watertightness. They can utilize a special tool to determine the water-tightness and strength of your windows and ensure they meet the industry standards. If your windows fail the test, they will require replacement. It's a costly repair, but worth it to ensure the safety and comfort of your family.

Sagging

If your windows don't shut properly, it could lead to a number of issues, such as drafts condensation and a rise in energy bills. It could be a sign that the windows weren't well fitted at installation or the sealant is no longer working. There are a few things you can do to resolve the issue.

To fix your window properly it is essential to set up a work space with plenty of natural light. Begin by laying down newspaper or an old blanket to shield the flooring from any splinters or drips that may fall from windows while you work.

Use a white cloth, soaked in a mixture of water and detergent. This will help prevent any stains of color appearing on your windows. Note the the hinge channel on your uPVC window when you are ready to begin working. Then, remove the channel from the frame and fill the screw holes using epoxy (for uPVC windows) or wood filler (if your frames are constructed from wood). Make sure to smooth out the hole that you have filled before it sets.

Reinstall the hinge channel after the holes have been filled. Make sure you center it on the window jamb, and drill the new screwholes about a quarter-inch away from the original locations.

Next, measure the length of the spindle that protrudes from the underside of the handle and then order a replacement online or bring the old one in to an hardware store to get a matching. Remove the setscrew from the operator shaft. File it flat to allow the set screw to lock onto the shaft. Now your uPVC window should close easily.

Broken Hinges

If your uPVC window hinges are damaged or aren't functioning properly and you are unable to open or close the window, it will be difficult to open or close the window. This could be a security issue and can also stop your home from staying warm or cold. It's simple to purchase a new window hinge for your uPVC windows. However, it's important to make sure you have the right type of hinge for your windows.

This is because the hinges have to be of the same width to fit into the frame of the window. The most common type of hinge used in windows made of uPVC is an 15mm or 18mm UPVC window hinge. There are also specialised hinges for wooden frames. Getting the correct type of window hinge for your windows can aid in avoiding common problems that many homeowners encounter with their windows, like not closing properly.

There are several reasons why your window hinges may have become stiff or loose. The hinges might not be tightened enough. You can test this by using a screwdriver to locate the friction screw at the end of the hinge, and then loosen it. You can then adjust it by turning it either way.

Call Preston Glass Fix if your Upvc Repair window's hinges aren't functioning properly. We can provide an immediate solution. Our technicians will examine the condition of your window hinges and recommend the best solution for you. We can replace your window hinges, adjust them or install new locking mechanisms to ensure that your UPVC windows are secure and safe for years to come.

Locks that aren't working

UPVC window mechanisms and locks are an essential part of home security. They make it very difficult to open a window without breaking into the house. It can be a hassle when a lock fails but you don't have to replace the entire window.

Most of the time, it's a minor issue that could have been prevented if you have had regular maintenance. This is the reason we recommend that you have your uPVC windows maintained regularly using our yearly maintenance package to minimize the risk of having problems.

Most modern uPVC windows come with espagnolette locks which operate by pushing the handle's nose across a wedge block and then turning the handle to close the lock. They are extremely efficient in keeping the window closed, however with time, they may begin to fail if they are not properly maintained - we recommend applying WD-40 to the lock a couple of times per year.

If you notice that your uPVC windows aren't opening and close as smoothly as they used to or If the lock isn't working properly it is likely that there is a problem with the locking gearbox within the window frame. It can be difficult to access this because it requires the removal of seals around the frame and the removal of the handle (be cautious not to damage the seals).

A locksmith who specializes in UPVC repairs has the knowledge to quickly identify the issue and then be able to replace the failed locking gearbox with a exact replacement. This simple and quick fix can save you hundreds of dollars by avoiding having to buy new windows.