Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to professional auto locksmiths with the right equipment and technical knowledge. They will be able to make and program new keys much quicker than a dealership and at a lower cost.

If the key fob has stopped locking or unlocking your doors it could be due to a dead battery in the coin. However, there are many other reasons why the key might be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your peugeot car key replacement 208 from locking and unlocking, and also stopping it from starting the engine. If this is the case, you'll have to use the backup starting method that is detailed in the owner's manual to your vehicle.

The spark plugs might also be worn out. The spark plugs ignite the fuel to start the engine. However, they have a limited lifespan. If they're not used enough, they will eventually fail.

There is a simple solution for this issue. Examine the voltage of your battery using a multimeter. If the voltage is less than 11,5 volts then it's time to replace it. It is also essential to clean the contacts of the battery when it has corrosion. This can be done by removing the rubber covers from the two battery terminals, and then using a wirebrush, you can remove any corroded battery parts. Then, you should connect the cables to the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery is not empty, you must ensure that the spark plugs are working. It is possible that they are overly dirty, which causes them not to spark. The spark plugs can be cleaned in the workshop.

Peugeot cars use a transponder style key that works with the car's immobiliser system. This ensures that only the correct key can turn the engine. If the chip inside the peugeot boxer key key is damaged, it will not send the correct signal to the vehicle.

This is a typical issue that can be caused by water damage. This is a frequent issue in warmer climates where the vehicle is exposed to rain or snow. If this is the case, get in touch with a reputable locksmith who has all the equipment and tools needed to change the key's programming. They also have the most up-to-date technology and equipment needed to create the Peugeot 208 smart key. The process shouldn't last more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the old carbon encased transponder chips to an entirely new type of chip that incorporates electronic components that are placed on a circuit board. The new system is excellent when it's new, however the circuit boards begin to degrade with time and stop working properly.

This can prevent the immobiliser from triggering so that your vehicle will not start. If this is the case, it's a good idea get in touch with a Peugeot specialist or locksmith.

Another common issue is when the battery for the key fob gets depleted, which causes the key blade to stop feeding into the lock. A car locksmith will replace the battery and then cut a fresh blade for you. This is a simple fix.

Faulty Receiver Module

It could be that the receiver module is malfunctioning in the event that your Peugeot key fob stops working after being dropped on the floor, exposed to a sudden rainstorm or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which manages the central locking system of your Peugeot vehicle.

Rubber seals on the key fob block water from reaching its electronic chip. The chip can be damaged by water if it is exposed to water for long periods of period of. The high salt content of the pool or ocean waters could cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This is only done by an expert auto locksmith or Peugeot specialist. In contrast to other vehicles, Peugeot keys are protected by an exclusive immobilizer system that requires the right coding for the start of the engine. This is why it is imperative that you should only rely on an authorized Peugeot locksmith to create and program an alternative.

Computer malfunctioning on-board

The computer on board of your Peugeot is responsible for a variety of features in your car, including power windows and airbags. The on-board computer displays a code if something goes wrong. This code will be stored within the system until the issue is fixed. In most cases, this will require replacing the on-board computer.

The most frequent cause for the warning light of the airbag to come on is corroded or loose connections in the sensor. It can be due to wear and tear, ageing or exposure to moisture and salt. This issue must be addressed as soon as you can, as an airbag that is malfunctioning could be dangerous in the event in the event of an accident.

If your Peugeot is showing a card not detected error then the key battery in the key fob may be weak or dead. This will stop the key fob from sending a signal to disable the vehicle's immobilizer. Test this by pressing the unlock button on the key fob, and then trying to start your vehicle. If it doesn't work, the key battery must be replaced.