Double Glazing Door Lock Repairs

Have your upvc door repairs near me window or door mechanism deteriorated? Perhaps the door or window handles aren't able to connect properly or are difficult to use.

It is crucial that your double glazed doors work smoothly, otherwise you'll be wasting energy and increase the chance of burglary. Owen the Locksmith can repair your door lock for a reasonable price.

Snapped Key

If a key is snapped off within the lock, it can be incredibly difficult. It could also be an issue for security, since the door may not be locked and make you open to intrusion. There are a few quick fixes you can make to resolve the issue and make your door functional again.

Be sure to remain calm. If you panic and start doing a lot of fumbling around you may end up pushing the damaged piece of the key deeper into the lock, which could make the situation worse.

Next, spray WD-40 or another penetrating oil into the lock to make the broken piece slip out more easily. You can also make use of a screwdriver to break up any stuck pieces that might be blocking the way. If you have a piece of the key that is stuck then grab it using a paperclip or another thin metal object and pull it. Both methods work well, but be careful not to push the broken piece of the key further into the keyway.

Some paperclips have grooved edges that could be used to extract hooks and some Jigsaw blades also work for this use. If you do not have any of these handy, you can make use of needle-nose pliers to bend them and create hooks. You can also make use of a pair of tweezers to grasp and pull out the remaining pieces of broken keys.

If you are unable to remove the broken piece of key then you can use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present within the lock.

If none of these solutions seem to work, it could be time to contact a locksmith. Fitlocks experts can fix issues such as broken handles and broken keys with uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to make them easier to operate. Request a repair for your double glazing with us online or give us a call to discuss your needs.

Broken Cylinder

A damaged cylinder poses a serious security threat. It's fortunately a simple repair for a professional locksmith to complete. A locksmith will have to tap the cylinder in order to repair it. This can be done using a hammer, or any other tool. However, the best method is to use a wire or a long match. Then, place the end of the match or wire in the keyway. The locksmith will hit the lock to break it open. This is much better than using a heavy hammer, which could harm the lock.

Overheating is the main reason behind cylinder heads cracking. This can happen when the cylinder head and block are made of various metals such as cast-iron and aluminium. Different metals can heat up and cool down at different rates. This could cause localized hotspots to expand faster than the rest of the cylinder.

Corrosion is a different reason for fractures in cylinders. If the cylinder block and head are not maintained correctly they may rust or corrode, which can cause them to expand faster than they would normally. In time, this could cause cracks.

If your uPVC window lock or door is stiff or requires a lot of pressure to turn, it could be due to several things. This can result from a defective locking mechanism or misalignment, and also a worn out handle.

This is a straightforward and affordable fix that the majority of homeowners with double glazing can perform. A professional locksmith should be able solve this issue within a matter of hours after arriving at your residence. They can replace the locking mechanisms, or change the window handles and change the gearboxes based on the specific requirements of your home. A locksmith with experience will always be able to advise you on the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security euro cylinders TS007 that provide an extra layer of security against burglars. This is a small price to pay for the peace of mind that comes with knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks may break. They have complex mechanisms which deteriorate over time. It isn't always easy to pinpoint the reason for the broken window handle lock and fix it correctly.

Repairing your damaged handle, whether it's the internal latch or the locking mechanism will increase the security of your uPVC door and reduce the risk of draughts. It could be costly to repair or replace your handle incorrectly and it can also damage the frame and the lock of your door.

Screwdriver When the window is open, loosen the screw holding the handle. This should be located on the inside face of the back plate, normally concealed by a screw cover for aesthetic reasons. It is important to not lose any internal parts of the handle like the plates and levers on either side. Ideally, keep them in the same place so you can replace them when needed.

Then, turn the handle to make it 90 degrees to the window frame and loosen the screw on the back of the handle that fixes it to the internal spindle using a second screwdriver. Once this is loose, you should be able to pull the handle off and pull out the broken spindle. Replace it with a new spindle, making sure it's the same length (you can find them online or in hardware stores). Screw it in the frame. Do not overtighten the screw as this could cause damage to the handle and window frame.

Make sure the new handle is installed after which you can close and test the handle. Hopefully, it will work smoothly and you'll be able to open your window once more.

Don't forget to double-check that your uPVC window is shut correctly when you're using the handle. If they're not closing properly then you may experience damp and draughts inside your home as well as compromising your home's energy efficiency. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is most common in uPVC tilt-and-turn windows. These windows require a handle that acts as an locking device within the frame of the window. The handle is attached to a central rod that activates a series of locks that are shaped like mushrooms and secure into the frame of the window keep. If the dead latch mechanism is not able to open after the handle has been turned, it's likely the spindle is damaged. This could be a problem that is frustrating.

Luckily there are ways to rectify this issue. A reputable locksmith will be able to quickly and efficiently repair this problem. They will be able to disassemble the window handle by using a tool that removes the wheel portion of the mechanism that is where the spindle goes. This can be done with no damage to the handle or window frame.

Once the wheel has been removed, the technician will inspect the spindle and determine what caused it to break. This involves disassembling the spindle, and then examining each component part, noting any damage or excessive wear. This procedure is typically carried out by technicians working in an environment that is clean.

The next step is to clean the damaged spindle. This will remove any debris or dirt that could be hindering its normal functioning. The spindle may then be repaired or replaced. If it is replaced, the technician will need a dowel of a similar size to the one used in the first and drill mating holes in both pieces of the spindle. This will ensure that the new spindle is precisely matched to the handle.

If the spindle that is damaged is beyond repair, it could be required to replace it completely. Home centres sell generic substitutes however if your window style is rare you'll have to speak with a cabinet maker or woodworker who can recreate the exact piece. After the spindle is installed, it is fixed to the handle. Place the screw holes on the handle to the existing screws in the frame. Once the new handle is firmly in place, you'll be able to operate your uPVC window.