How to Replace a Kia Sportage Replacement Key

For many Kia models keys, the key has a keyless entry system built-in. The key is usually akin to the remote control and can be exchanged with a brand new one from a Kia dealer or locksmith.

Key fobs may stop working due to a variety of reasons, including batteries that are dead worn buttons, signal interference, water damage and a malfunctioning receiver module. Here are some helpful tips to assist you in getting your kia sportage key fob sportage replacement key working once more.

How do you replace the remote key or the smart key?

The battery in your Kia's intelligent key will eventually have to be replaced, whether it's a remote or a push-to-start one, or a standard metal key that doesn't have a transponder. This is particularly relevant if your vehicle displays a message indicating that the remote or smart keys have low battery power.

This is a relatively simple process. To replace the battery of the key fob, remove the mechanical key from the slit on the back of the key fob and remove the cover. A small screw is found inside the key fob, which holds the battery in its place. Remove the old battery by removing the screw with a small screwdriver. Then insert the new one and close the slit on the key fob.

Once the key fob has new batteries check it by pressing the lock and unlock buttons. It's okay when the doors lock or unlock as expected. You can now make use of Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to do some errands in Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a computer which is available to the locksmith for cars or dealer. Other keys (non transponder keys made of steel) do not require programming. If your key has to be programmed again, you will need to be aware of the key code that is stamped on the key code tag and then record it in a safe place.

How do you replace a dead battery?

If your Kia key fob is not responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light coming on or the engine not working properly. It is relatively easy to replace key fob battery with just two tools.

Make sure to shut off your vehicle and close all doors before you begin. Find the small, metal or plastic piece that is on the bottom of your key fob, and jiggle it until a metal key pops out. Then, you can insert this key into the driver's door handle to unlock your car.

To replace the battery inside the key fob, remove the cover at the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Remove the old battery and then position the new battery to ensure that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or bending the metal contacts.

Once the new battery is installed after which you turn the key fob off and then on in the ignition several times until the door locks cycle. You can then test your Kia's key fob once more to ensure it's functioning properly.

How can you replace the smart key

You can have the standard keyfob or Smart Key, based on the model of Kia Sportage. The difference between them is that the smart key comes with the small blade of a key that is hidden inside, while the standard fob does not. Both key fobs are equipped with an internal battery that will eventually require replacement. This is an easy process which takes just two minutes.

Before you start it is essential to ensure that you are on a flat surface with sufficient lighting and that your Kia is turned off. Also, remember that there are small parts inside the fob which could fall out if you are not cautious.

The small release button is located on the lower backside. This will either be a circular silver button or a rectangular slot. When you press it the mechanical key blade will pop out and you can then open the key fob.

After the key fob has been opened, remove the battery. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. Once you're done, your key fob should allow you to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How do you replace the mechanical key?

The kia ceed key fob - from the Dnpaint Co blog - key fob is a fantastic convenience that allows us to lock and unlock our car at the push of a button. As with all devices it is possible that the Kia key fob can have issues at times. There are solutions to solve these issues and keep your key fobs in good working order for the duration of.

A dead or weak battery is one of the most common issues. This could cause your device to stop working or work intermittently. If this is the problem you should replace the battery an entirely new battery.

If this doesn't fix the problem, try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be sure not to damage any internal components, or scratch the plastic. After the battery has been removed and replaced with a brand new battery.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. Contact a dealer locksmith to resolve the problem in the event that the fob is not working. Make sure they cut you an emergency key that functions in all the trunk and door cylinders to avoid lockouts in the future.