How to Replace a Kia Sportage replacement kia key Key

For many Kia models, the key contains the keyless entry system that is built into the key. The key can be compared to an remote control, and can be replaced with a new one from a Kia dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, such as batteries that are dead, worn-out buttons signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key to work again.

How do you replace the remote key or the smart key?

If your Kia is equipped with an intelligent key, remote key push to start key or regular metal non-transponder key the battery in these keys will eventually need replacing. This is particularly the case if your car displays a message telling you that the smart or remote keys have low battery power.

Luckily, this is an easy process. To replace the battery on the keyfob, remove your mechanical key from the slot at the back of the fob. Then, you need to pry the cover off. A small screw is in the key fob to keep the battery in its place. By using a small screwdriver unscrew the screw and remove the battery that was in place. Then insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock or unlock buttons. It's okay when the doors lock or unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) don't require programming. If you're required to reprogramme your key, you'll need to write down the key code's number on the key code tag.

How to replace a battery

If the Kia key fob does not respond when you press the lock/unlock button, prices it is most likely that the battery is insufficient. A weak battery can cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately replacing the key fob battery is a fairly simple DIY project that requires just a few tools.

Before you begin the process before beginning the process, ensure that your vehicle is turned off and all doors are closed. Find the small metal or plastic piece on the bottom of the key fob. Press it until the metal key pops out. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover from the back and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then position the new battery to ensure that its "+" side faces you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the metal contacts.

After you have installed the new battery then turn the key fob on and off in the ignition until the door locks up. Then, test your Kia key fob to determine whether it's functioning properly again.

How do I replace a smart key

You could have an ordinary keyfob or Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade unlike the standard key fob, which does not. Both kinds of key fobs contain batteries inside that eventually will need to be replaced. This is a simple procedure that takes just two minutes.

Before you start it is important to make sure that you are on a flat surface with adequate lighting and that your Kia is turned off. Keep in mind that there are tiny parts inside the fob that could fall out if not vigilant.

The first step is to find the small release button on the back of the lower part of the fob. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, take out the battery that was in it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. Once you're done you should be able to lock and unlock your vehicle using your key fob - even if your engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing the button. Like any device like a key fob, the Kia may have issues. Luckily, there are steps to take to solve these issues and ensure that our key fobs are in good working condition for the long term.

One of the most common problems is a low or dead battery. This could cause your device to stop working or work intermittently. If this is the case try replacing the battery with a new one.

If this isn't enough to resolve the problem, try using a standard flathead screwdriver to wedge open the fob's plastic casing. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a new one.

Once the new battery is in, close and then open the doors with the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's functioning properly. Contact a dealer or locksmith to address the issue when the fob still is not working. Make sure they make you an emergency key that can work for all door and trunk cylinders to prevent lockouts in the future.