How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is an integrated keyless entry system. This key typically resembles the remote control and can be changed with a brand new one from an kia replacement key [new content from Thewrightbeef] dealer or a locksmith.

Key fobs can stop working for several reasons, including a dead coin battery, worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some guidelines on how you can get your Kia Sportage replacement key back to working.

How to replace a remote key or smartkey

The battery in your kia ceed key fob replacement's intelligent key will eventually require to be replaced, whether it's a remote key or a push-to-start one, or a normal metal key that doesn't contain an electronic transponder. This is especially true if your car shows a message that states the smart or remote keys are not powered by batteries.

Luckily, this is an easy procedure. In order to replace the key fob battery take the mechanical key from the slit on the back of the key fob. Next, pry open the cover. Inside the key fob there will be a small screw that holds the battery in the correct position. Utilizing a small screwdriver take the screw off and remove the old battery. Install the new battery and then close the slit on the key fob.

Test the key fob by pressing the lock and unlock buttons. You're in good shape If the doors lock and unlock as expected. You can now make use of the Kia's hands-free lock/unlock feature whenever your fingers feel cold or you need to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a machine for programming, which is only available to the automotive locksmith or dealer. Other keys (non-transponder metal keys) don't require programming. If your key has to be programmed, you will need to be aware of the number stamped on the tag that identifies the key and keep it in a safe location.

How to replace a battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A battery that is not functioning properly could cause other issues, such as the check engine light flashing on or the engine not cranking. Fortunately, replacing the battery on the key fob is a relatively simple DIY project that requires just a few basic tools.

Before beginning the process ensure that your vehicle is off and all doors are closed. Find the small, metal or plastic piece that is on the bottom of your key fob and move it until a metal key slides out. This key can be put into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover from the back and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and align the new battery in a way that the "+" positive side is facing you, and the "negative" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or breaking the contacts of the metal.

Once the new battery has been installed then turn the key fob off and then turn it on in the ignition for a few times until the door locks cycle. Then, test your kia picanto key replacement key fob to check whether it's working again.

How to replace the smart key

Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The difference is that the smart key comes with tiny mechanical key blade in it, whereas the standard fob does not. Both key fobs have a battery that will eventually need to be changed. It's an easy process that takes only two minutes.

Before you get started it is important to ensure that you are on a flat surface with adequate lighting and that your Kia is off. Be aware that the fob has small pieces that could fall when you're not careful.

The release button for the small size is located on the lower backside. It can be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open then you can take off the old battery and replace it. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. Once you're done, your key fob will allow you to lock, unlock, and start your vehicle, even if it isn't running.

How do you replace the mechanical key

The Kia keyfob is a great convenience which allows us to lock or unlock our car by simply pressing a button. However, like all devices it may have issues at times. There are ways to resolve these issues and keep your key fobs running for the duration of.

A dead or low-quality battery is among the most common problems. This can cause your fob to stop working or operate intermittently. If this is the case then try replacing the battery with a fresh new one.

If this does not solve the issue, use the flathead screwdriver that is standard to wedge the fob's casing made of plastic open. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a new one.

When the new battery is in, close and then open the doors using the mechanical key (every Kia fob has an emergency mechanical key that will fit in the slot). Test the key fob to confirm it's working as intended. Contact a dealer, or a locksmith to fix the issue in the event that the key fob is not working. To avoid locking outs in the future, make sure you get an emergency key that can work on all trunk and door cylinders.