Double Glazing Door Lock Repairs

Are your uPVC window or door mechanism faulty? Perhaps the handles on your uPVC windows or doors are not aligned properly or double glazing repair are difficult to use.

You'll lose energy in the event that your double-glazed doors fail to perform as they should. This increases the likelihood of burglaries. Owen the Locksmith can repair your door lock at a reasonable cost.

Snapped Key

It can be a hassle when a key is snapped into the lock. It also poses an issue for security, since the door may not be locked and could leave you open to intrusion. There are a few quick fixes you can try to repair the issue and get your door working again.

The first step is to remain calm. If you panic you may end up pushing the damaged key further into the lock.

Then, spray WD-40 or another penetrating oil into the lock to aid in making the broken piece to slide out more easily. You can also make use of a screwdriver to break up any stuck pieces that might be blocking the way. If you're fortunate enough to have a small piece of the key sticking out and you want to remove it, make use of a paperclip or other metal object that is thin to grab it and then pull it out. Both methods work, but you must be careful not to push the broken key piece further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades are also well for this. If you don't happen to have one of these tools, you can bend a hook using needle-nosed pliers. Additionally, you can make use of a pair of tweezers to grab and remove the last bit of the broken keys.

If you are unable to get the broken piece of key out, you can try using a lock de-icer. It's available in many hardware stores and is used to freeze any moisture that may be present within the lock.

If none of these solutions seem to work, it may be time to consult a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to make them more user-friendly. Get a double glazing repair via our website or give us a phone call to discuss your needs.

Broken Cylinder

A damaged cylinder can pose an immediate security risk. It's fortunately a simple repair for a professional locksmith to complete. To fix the cylinder a locksmith will need to tap it. This can be done using the hammer or other tool. However, the most effective method is to use a wire or a long match. Then, put the match's tip or wire near the keyway. The locksmith will then hit the lock to crack it. This is much safer than using a heavy hammer that can cause damage to the lock.

The most common cause of cylinder head cracks is overheating. This can occur when the cylinder block as well as the cylinder head are made of different metals, such as cast iron and aluminium. When various metals are heated and cool at different rates, it could create hotspots in the local area that expand faster than the rest of the cylinder head, leading to cracks.

Another possible cause of cracks in cylinders is corrosion. If the cylinder head and cylinder block are not properly maintained, this can lead to rusting or corrosion and cause them to expand at a greater rates than they should. In time, this could also lead to cracks.

If your uPVC window or door lock is rigid and requires a lot more pressure to turn it could be due to a variety reasons. A defective locking mechanism, misalignment, or the wear of the handle are typical causes of this problem.

This is a straightforward and inexpensive fix that most double glazing owners can do. A professional locksmith will usually fix this problem within one hour of arriving at your home. Depending on your needs they will be able to replace the locking mechanism, change the window handles, or change the gearboxes. A professional locksmith will be able to provide you with a recommendation on the most cost-effective solutions for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders that offer an additional layer of protection against burglars. This is a small cost to pay for the peace of mind that comes with knowing your upvc repair doors are secure.

Broken Handle

It's not surprising that window handle locks could break. They have intricate mechanisms that wear out over time. It isn't always easy to pinpoint the reason for the problem and repair it correctly.

Fixing your broken handle, regardless of whether it's the internal locking mechanism or latch, will improve the security of your uPVC door and stop draughts. It could be costly to replace or repair the handle in a way that isn't done correctly. It could also harm the frame and the lock of your door.

Screwdriver When the window is open and the screw loose, loosen the handle. This should be located on the inside face of the back plate, normally hidden by an aesthetically pleasing cover for the screw reasons. Be sure to not lose any internal parts within the handle, for example the levers or plates on the opposite side of the spindle. It is best to keep them in the same order so that you can replace them in the event of a need.

Then, rotate the handle until it's 90 degrees towards the window frame. Then, loosen the screw on the back of the handle that fixes it to the internal spindle with another screwdriver. Once the screw is loose, you should be able to pull the handle away and pull out the broken spindle. Replace it with a new spindle, ensuring that it's the same length (you can find them online or at hardware stores). Screw it in place. Do not tighten the screw too much as this can damage the handle and the window frame.

Ensure the new handle is installed Close the window and test the handle. Hopefully, it will work smoothly and you'll be able open your window once more.

While you're working on the handle, don't forget to ensure that your uPVC windows are shut correctly. If they don't, you could experience damp and draughts inside your home as and also affecting your home's energy efficiency. A local window company, like Core Sash Windows, will be able to adjust the hinges on your window frames to ensure they shut correctly.

Broken Spindle

It is more common for the spindle to break rather than the handle. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that acts as a locking mechanism within the window frame. The handle is attached a central rod that triggers the cams with a mushroom shape that secure into the frame of the window keep. If the dead latch mechanism is not able to open when the handle is turned it is possible that the spindle has broken This can be an extremely frustrating issue.

Fortunately there are ways to fix this problem. A good locksmith can quickly and effectively fix the issue. A reputable locksmith can disassemble the window's handle using a tool that removes the wheel part that houses the spindle. This can be done without damaging the handle or causing other damage to the frame of the window.

After removing the wheel, the technician will inspect the spindle and determine the reason for its break. This involves breaking the spindle into its constituent components and carefully observing their general condition, as well as any particular areas of wear or damage. This procedure is typically performed by technicians in an environment that is clean.

The next step is to clean the damaged spindle. This helps eliminate any dirt or debris that could be hindering its normal functioning. After that the spindle can be repaired or replaced. If the technician is replacing the spindle the dowel can be used that is the same size to the original. Then, he will drill matching holes into both pieces. This ensures that the new spindle has an exact fit with the handle.

If the spindle is damaged and cannot be repaired, it might need to be replaced entirely. Home centers offer generic replacements. However, if the style of your window is unusual then you will need to find a woodworker or cabinet maker who can make the exact component for you. Once the new spindle is in place it can be fitted to the handle by lining up the screw holes in the handle with the frame's existing screws. Once the handle is seated, you can operate your uPVC windows.