Double Glazing Door Lock Repairs

Are your uPVC window or door mechanism not working properly? Perhaps the window or door handles aren't able to connect properly or are hard to use.

You'll lose energy when your double-glazed doors do not work properly. This also increases the chance of burglary. Owen the Locksmith can repair your door lock at a reasonable cost.

Snapped Key

It can be frustrating when a key snaps into the lock. It could also be an issue for security, since the door may not lock and leave you vulnerable to burglars. Fortunately, there are simple fixes you can use to solve the issue and get your door functioning properly once more.

Remember to remain calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Next spray WD-40 or another penetrating oil into the lock to make the broken piece to slide out more easily. You can also use a screwdriver to help break up any stuck pieces that might be blocking the way. If you have a piece of the key that's still sticking out and is not being removed, grab it with the help of a paperclip or any other thin metal object and pull it. Both of these methods work, but be cautious not to push the broken piece of the key even further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't happen to have any of these then you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers can be used to grasp and pull out the remaining part of the broken key.

If you are unable to get the broken piece of the key out, try using a lock de-icer. It's usually available at most hardware stores. It works by freezing any water or ice that could be inside the lock.

If none of these strategies are working you, it's time to call locksmith. Fitlocks specialists are able to quickly resolve issues with uPVC door mechanisms and locks that have snapped keys as well as broken handles. They can also reconfigure your double glazing door mechanisms to allow them to operate more easily. You can book repairs to your double-glazing online or contact us to discuss your requirements.

Broken Cylinder

A damaged cylinder poses a serious security threat. It's fortunately a simple repair for a professional locksmith to complete. Locksmiths will need to tap the cylinder to fix it. This can be accomplished with the hammer or other tool. However, the most effective method is to use a wire or a long match. The match or wire's end in the keyway. The locksmith will then strike the lock to break it. This is much better than using a hammer that could harm the lock.

Overheating is the most common reason behind cylinder heads cracking. This can occur when the block and cylinder head are made from different metals like cast-iron and aluminum. When different metals are heated and cool at different rates, it could cause localised hotspots that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion is a different reason for fractures in cylinders. When the cylinder head and cylinder block are not maintained properly, this could cause corrosion or rust, which may cause them to expand at a a higher rate than they ought to. In time, this could also lead to cracks.

If your uPVC window lock or door is brittle or requires lots of pressure to turn, it could be due to several things. A defective locking mechanism, misalignment, or a worn handle are common causes of this issue.

It is a quick and cost-effective fix that a majority of homeowners with double glazing can perform. A professional locksmith will typically be able to solve this issue within a matter of hours of arriving at your home. They can repair the locking mechanisms, or change the window handles, and also change the gearboxes, based on your particular requirements. A professional locksmith will be able to provide you with a recommendation of the most cost-effective solution for your home. They can also suggest upgrades to the highest-security 3 Star Euro cylinders, TS007, that will provide an extra layer of security against burglars. This is a small cost to pay for the peace of mind that comes from knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks could break. They are equipped with complex mechanisms that wear out over time. If yours breaks, it can be difficult to determine the source of the issue and make sure you fix it properly.

Fixing your broken handle, regardless of whether it's the internal latch or the locking mechanism, will improve the security of your uPVC door and prevent draughts. It is costly to repair or replace your handle if it is not done correctly and could also harm the frame and the lock of your door.

Screwdriver When the window is open remove the screw that holds the handle. The screw should be on the inside of the backplate, usually concealed by a screw cap for aesthetic reasons. Be sure to not lose any of the internal parts within the handle, such as the plates or levers that are on either side of the spindle. Keep them in the same order to make it easier to replace if necessary.

Then, turn the handle until it's 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle by using a second screwdriver. Once the screw is loose, you can pull the handle out and take the broken spindle out. Replace it with a new one, ensuring it is the same length as the old one (you will typically find them online or in hardware stores) and then securely screw it in place. Do not tighten the screw too much as this could cause damage to the handle and window frame.

Close the handle and test it. The hope is that it will function smoothly and you'll be able to open your window again.

Make sure to check that your upvc repairs near me window is shut properly when you're using the handle. If they're not, you could experience damp and draughts inside your home, as well as compromising the efficiency of your home's energy usage. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames so they shut correctly.

Broken Spindle

It is often the case that the spindle inside a handle breaks rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These types of windows require a handle that operates a locking mechanism in the frame of the window. The handle is attached to a rod in the centre that is then activated by a series of mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism fails to open when the handle has been turned, it is most likely the spindle is broken. This could be a frustrating problem.

Luckily, there are steps that can be taken to remedy this situation. A good locksmith can quickly and efficiently fix this problem. A good locksmith will be able to disassemble the handle of the window by using a tool to remove the wheel part in which the spindle is. This can be done without causing any damage to the handle or causing any other damage to the window frame.

After removing the wheel, the technician can examine the spindle and identify the reason for its break. This involves breaking the spindle into its individual components and carefully observing their general condition, as well as any particular areas of damage or excessive wear. This procedure is typically carried out by technicians working in an environment that is clean.

The next step is to clean the damaged spindle, this assists in removing any dirt or other debris that might be obstructing its normal operation. After that, the spindle can be repaired or replaced. If it is being replaced the technician could use the dowel that is similar in size to the one used in the first and drill mating holes into both parts of the spindle. This will ensure that the new spindle is a precise fit with the handle.

If the spindle that is damaged is beyond repair, it could be necessary to replace it completely. Home centers sell generic replacements however if your window design is unique, you will require contacting an expert in woodworking or cabinet making who can replicate the exact component. Once the new spindle has been installed it can be positioned to the handle by lining up the screw holes in the handle and the frame existing screws. Once the new handle is firmly seated you will be ready to operate your uPVC window.