How to Replace a Kia Sportage Replacement Key

For many Kia models keys, there is a keyless entry system built-in. The key functions like a remote control and can be exchanged by a Kia dealer.

Key fobs can fail to function due to a variety of reasons, including an inactive battery, worn out buttons signal interference, or water damage. Here are some suggestions on how to get your Kia Sportage replacement key to work again.

How to replace the remote key or smartkey?

Whether your Kia comes with an intelligent key, remote key, push to start key, or a regular non-transponder steel key, the battery in these keys will eventually need replacement. This is particularly true if your car shows a message that states the smart or remote keys are not powered by batteries.

It's a relatively simple process. To replace the battery in the keyfob, remove your mechanical key from the slit that is located at the back of the fob. Then, pry the cover off. A small screw will be inside the key fob to keep the battery in its place. Take out the old battery by unwinding the screw with the help of a small screwdriver. Then, insert the new one and close the hole in the key fob.

When the key fob is equipped with a fresh battery, test it by pressing the locks and unlock buttons. If the doors lock and unlock in the same way, you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get chilly or when you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a machine for programming which is available to the locksmith who works for the automotive dealer. Other keys (non transponder keys made of metal) do not require programming. If you need to reprogramme your key, you'll need write down the key code's number on the tag for the key code.

How do I replace the battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A weak battery could cause other issues, like the check engine light appearing or the engine not cranking correctly. Fortunately replacing the battery on the key fob is a fairly simple DIY project that requires only a few tools.

Make sure that you shut off your vehicle and close all doors before you begin. Locate the small metal or plastic piece at the bottom of your key fob and gently jiggle it until the metal key slides out. This key can be put into the driver door handle to unlock your car.

To replace the key fob's battery, remove the rear cover and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and align the new battery to ensure that the "+" positive side faces you and the "-" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts on the metal.

After installing the new battery and turning the key fob off and on in the ignition until the door locks up. You can then test your kia picanto key replacement's key fob once more to ensure it is working correctly.

How do you replace a smart keys

Depending on the model of the Kia Sportage, you may have the standard key fob, or a smart key. The smart key has an embedded mechanical key blade, while the standard key fob does not. Both kinds of key fobs come with an internal battery that will eventually have to be replaced. Fortunately, this is quite simple and takes just two minutes.

Before you get started it is essential to make sure that you are on a flat surface with enough lighting and that your Kia is turned off. Remember that the fob has tiny parts that could fall if you're not careful.

The first step is to locate the small release button on the lower backside of the fob. It will be a circular or rectangular slot. When you press it mechanical key blade, it will pop out and you will be able to open the key fob.

After the key fob has been open, remove the old battery. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts shop. Once you're done it should be possible to lock, unlock and start your car with your key fob, even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob can be a fantastic convenience that allows us to lock or unlock our car simply by pressing a button. Like all devices, the Kia key fob might have issues. There are ways to troubleshoot these issues and ensure that our key fobs are in good working order in the long run.

One of the most frequently encountered problems is a weak or dead battery. This can cause the device to stop working completely or even to stop working intermittently. If this is the case try replacing the battery with a fresh new one.

If this isn't enough to resolve the issue then try using a normal flathead screwdriver to wedge open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

When the new battery is in, close and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that can fit in the slot). Test the fob to make sure it's functioning properly. Contact a dealer, or a locksmith to resolve the problem if the fob is still not working. Make sure they make you an emergency key that works across all trunk and door cylinders, to avoid future lockouts.