How to Replace a Hyundai I10 Key Fob Battery

The Hyundai i10 is one of the most stylish and elegant mini cars available. Its interior is more luxurious than its rivals such as the Citroen C1, Volkswagen UP and SEAT Ibiza.

Hyundai's key fob can do much of the work for you, including locking and unlocking your car remotely. It also has a physical key, which can be used in the event that the fob battery dies.

Dead Coin Battery

The key fob is a fantastic invention that allows drivers to lock and start their cars without the need for a physical key in the ignition. It does this by using radio frequency signals that connect to the car's onboard computer.

The battery in the keyfob controls the communication. It will eventually become worn out and will need to be changed. Based on the model of your Hyundai key fob, it may or may not display a warning when the battery has died. Keep a spare keyfob with you to swap out the battery as quickly as it wears.

Once the new battery is in place the key fob will need to be reprogrammed in the car. This can be done using an OBDII or Hyundai Digital Key scanner, however it is more convenient to do at your Reno home. Follow the steps in the owner's manual or search YouTube for"how to replace and open the Hyundai keyfob battery." Be sure to take a picture of the old battery or note it down prior to removing it.

Once the key fob is changed, it should work again. If it doesn't, you'll need to go to a dealer for a new key fob or call a locksmith on the move. They'll have the experience and tools to fix it.

Water Damage

A key fob can be a useful piece of technology that allows you to lock your car from the safety of your home, roll down the windows from outside and even begin the vehicle. But, it's not impervious to damage and will eventually wear out from normal use. The procedure of replacing the Hyundai keyfob battery i10 is relatively simple and inexpensive.

It's not uncommon to drop your key fob into the pool, a puddle or even washing machine. It's possible to retrieve it if you act fast. Water isn't a good mix for electronics, and a wet key fob can cause a myriad of problems, including corrosion, short circuits and even complete failure.

The first thing you must do is try to get as much water as you can. Shake out any visible moisture by flipping the fob. You can also employ a hairdryer or set it on a radiator to speed up drying. After removing all the moisture you can, place the fob in a warm place where it will dry out for a few days.

Then, you can open the fob in order to remove the battery that was in it. Most Hyundai I10 keys utilize the same type of battery used in many quartz watches, and are very simple to replace. Once you've replaced the battery, you must capture a picture or take a note of how it's placed prior to closing the fob.

Poor Battery Contact

It's possible that your keyfob's battery is getting worn out. This is a common problem, and usually the remote begins to show signs of trouble before it is completely gone. Make sure the clips are not corroded or loose. If you do, clean them using the appropriate battery cleaning solution and wire brush. Use a button cell battery that has the same size, voltage and specifications as the original.

It may also be an indicator that your alternator, the component that charges the battery while the engine is running, is not functioning correctly. An alternator that is not working properly will drain the battery rapidly, causing the warning light to turn on.

A quick check of the voltage can assist you in determining if this is the case with your Hyundai. If the battery is good it's possible the problem is with the circuit board or a different part of the key fob. Press a small metal button or tab on the front or the back of the key fob to open it. After removing the cover, replace it with a new CR2032 battery, making sure that all the connections are connected.

Reprogramming

Hyundai tucson key replacement offers keyless entry in several of its models. This makes cruising around Littleton and Parker, CO, easier than ever. You can use remotes to start your car, open the doors, and lock them. But it's not impervious to destruction and a damaged key fob can cause problems. If your Hyundai keyfob fails to function it may be necessary to reset it so that it functions with your vehicle.

First, you need to remove the battery. Typically, the button cell battery is located inside of the tab made of plastic. If you decide to open the tab and replace the battery, be sure to use the same size and voltage as your old battery.

When the battery is replaced close the tab and replace the retaining clips. Test the key fob to ensure that it works.

If the key fob doesn't work, it could be time to call an authorized locksmith or dealer. A dealer or locksmith can create a new key and remote and program it so that it can work with your vehicle. The cost for this service is typically priced, but it's worth it if you want to keep your Hyundai key fob running. They can also help you in locating the best hyundai key fob replacement key fob for your requirements.