How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, there is a keyless entry system built-in. The key is usually akin to the remote control and is able to be replaced with a brand new one from a Kia dealer or locksmith.

Key fobs are prone to malfunction for a variety of reasons, such as batteries that are dead, worn buttons signals, signal interference, water damage and a damaged receiver module. Here are some tips to assist you in getting your Kia sportage replacement key to work again.

How to replace the remote key or the smart key?

If your Kia comes with an intelligent key, remote key, push-to-start keys, or a standard non-transponder key made of metal, the battery in these keys will eventually need replacing. This is especially true if the vehicle displays a message that indicates that the smart or remote key is not powered by the battery.

It's a simple process. To replace the keyfob battery remove the mechanical key from the slit on the back of the fob. Then, push the cover open. A small screw is found inside the key fob to hold the battery in place. Using a small screwdriver, take the screw off and remove the old battery. Then, insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you have to go on errands around Brandon.

Note: Certain key fobs might need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of steel) do not require programming. If you're required to reprogramme your key, you'll have to note the key code's number on the key code tag.

How do you replace the battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A battery that is not functioning properly could cause other issues such as the check engine light coming on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a relatively easy DIY project that requires only a few tools.

Make sure to shut off your vehicle and close all doors before you begin. Find the small, metal or plastic piece at the bottom of the key fob. Press it until the key pops out. Then, you can insert the key in the handle of the door for the driver to unlock your car.

To replace the battery in the key fob remove the cover that covers the rear. Make use of a plastic pry tool to loosen the latch that holds the black negative cable. Remove the old battery and align the new battery in a way that the "+" positive side faces your face and the "negative" negative side is facing the fob's electronic contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or bending the metal contacts.

Once the new battery has been installed, turn the key fob off and on in the ignition for a few times until the door locks cycle. You can then test the Kia's key fob once more to ensure it's working properly.

How can you replace the smart key

Depending on the model of your kia key replacement Sportage, you may have a standard key fob or a smart key. The smart key is equipped with an embedded mechanical key blade, however, the standard key fob does not. Both types of key fobs have batteries that will eventually have to be replaced. It's an easy task that takes just two minutes.

Before you get started it is essential to make sure that you are on a level surface with sufficient lighting and that the Kia is off. Keep in mind that there are small parts inside the fob that could be removed if not vigilant.

The small release button is located on the lower backside. It can be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the battery. The new battery is CR-2032, and can be bought online or in your local auto parts store. Once you're done, you should be able to lock or unlock your vehicle using your key fob, even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is a wonderful convenience that lets us lock or unlock our car by pressing the button. But, as with all devices, it can have problems occasionally. Luckily, there are methods to solve these issues and ensure that our key fobs are in good working condition for the long term.

A dead or weak battery is one of the most frequent problems. This could cause your device to stop working or work intermittently. If this is the problem then replace the battery with a new one.

If this isn't enough to resolve the problem you can try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed then replace it with a brand new battery.

When the new battery is installed, close and unlock the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's working properly. If the device isn't working, contact an authorized locksmith or dealer to solve the issue. Make sure they make you an emergency key that functions in all the trunk and door cylinders in order to avoid future lockouts.