How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with a built-in keyless entry system. The key is usually akin to a remote control and can be replaced with a new one from a kia Key fob replacement dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, such as batteries that are dead, worn-out buttons signals, signal interference or water damage. Here are some helpful tips to help you get your Kia sportage replacement key working once more.

How to replace the remote key or smartkey

The battery inside your Kia's smart key will eventually require to be replaced, regardless of whether it's a remote key as well as a push-to start key or a normal metal key that is not equipped with a transponder. This is particularly relevant if your car displays a message telling that the smart key or remote is not powered by the battery.

It's a simple procedure. In order to replace the battery of the key fob remove the mechanical key from the hole in the back of the key fob and pry open the cover. A small screw is inside the key fob to keep the battery in place. Remove the old battery by unscrewing the screw using the help of a small screwdriver. Then, you can insert the new battery and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go If the doors lock and unlock as expected. You can now utilize the hands-free lock/unlock feature on your Kia when your fingers start to get cold or you have to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal), do not need programming. If you're required to reprogramme your key, you'll need write down the key code's number on the tag for the key code.

How do you replace the battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it's likely that the battery is low. A low battery can also cause other issues, like the check engine light appearing or the engine not running properly. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires only a few basic tools.

Make sure you turn off your vehicle and close all doors prior to beginning. Find the small metal or a plastic piece at the bottom of the key fob. Then, jiggle it until the metal key falls out. The key can be put into the driver door handle to unlock your car.

To replace the battery on the key fob, remove the cover at the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Remove the old battery, and then align the new one in a way that the "+" positive side is facing you, and the "negative" negative side is facing towards the fob's metal electrical contacts. Avoid using excessive force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

After installing the new battery and turning the key fob off and on in the ignition until the door locks cycle. You can then test the kia key replacement's key fob to ensure it's working properly.

How to replace a smart keys

You may have either a standard keyfob or a Smart Key based upon the model of Kia Sportage. The difference is that the smart key is equipped with an incredibly small key blade hidden within it, whereas the standard key fob does not. Both types of key fobs are equipped with batteries that will eventually have to be replaced. It is a simple process which takes just two minutes.

Make sure you turn off your Kia and sit on a flat well-lit and well-lit area before you begin. Also, remember that there are tiny pieces inside the fob that could fall out if you are not cautious.

The first step is to find the small release button that is located on the back of the lower part of the fob. It will be a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to take off the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. When you're done, the key fob should be able to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do you replace a broken mechanical key

The Kia key fob is a wonderful option that lets us lock and unlock our car with the press of one button. But, as with all devices it will encounter issues from time to time. Luckily, there are methods to solve these issues and keep our key fobs in good working condition in the long run.

A low or dead battery is among the most common issues. This could cause the fob to stop working entirely or work intermittently. If this is the case then try replacing the battery with a fresh new one.

If this doesn't solve the issue, you can use an ordinary screwdriver with a flat head to wedge the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed and replaced with a brand new one.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob to ensure that it's working correctly. Contact a dealer or a locksmith to fix the issue in the event that the fob is not working. To avoid locking outs in the future, ensure you purchase an emergency key that will be able to work with all door and trunk cylinders.