Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC door or window mechanism faulty? Perhaps the handles on your uPVC windows or doors aren't aligned correctly or are difficult to use.

You'll be wasting energy when your double-glazed doors do not work properly. This increases the risk of burglary. Owen the Locksmith will be able to repair your door lock at reasonable costs.

Snapped Key

If a key is snapped off within a lock, it could be extremely difficult. It can also be a security problem because it could expose you to a burglar if the door is not locked. Fortunately, there are some quick fixes you can use to solve the issue and get your door working properly once more.

Be sure to remain calm. If you get scared and start doing a lot of fumbling around, you might just end up pushing the broken piece of the key further into the lock, which could make the situation worse.

Next spray WD-40 or another penetrating oil into the lock to make the broken piece to slide out more easily. You can also use the screwdriver to break any pieces that are stuck. If you're fortunate enough to have a small piece of the key sticking out it, you can make use of a paperclip or other thin metal object to grab it and then pull it out. Both methods work, but be careful not to push the broken key further into the keyway.

Some paperclips have grooved edges that can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these items then you can bend a hook with needle-nosed pliers. Also, a pair tweezers can be used to grasp and pull out the last bit of the broken key.

If you are unable remove the broken piece of key, use a lock deicer. It is available at all hardware stores. It is used to freeze any moisture or ice that might be in the lock.

If none of these tricks seem to be helping you, it's time to call a locksmith. Fitlocks experts can quickly solve problems with uPVC door locks and mechanisms such as snapped keys and broken handles. They can also reconfigure your double glazing door mechanisms to allow them to operate more easily. You can book repairs to your double-glazing online or call us to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a major security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. Locksmiths will need to tap the cylinder to fix it. This can be accomplished with the hammer or other tool. The best method is to employ a wire or long match. Then, place the match's tip or wire close to the keyway. The locksmith can then strike the lock in order to crack it. This is far better than using a heavy hammer that can cause damage to the lock.

Overheating is the most common cause of cylinder heads cracking. This can occur when the cylinder block and head are made of different metals, such as cast iron and aluminium. When different metals heat up and double Glazing cool down at different rates, it can create hotspots in the local area that expand faster than the rest of the head of the cylinder, leading to cracks.

Corrosion is a different reason for fractures in cylinders. If the cylinder head and the cylinder block aren't maintained properly, this could cause corrosion or rust, which may cause them to expand at a higher rate than they should. Over time, this can also lead to cracks.

If your uPVC window or door lock is stiff and requires a lot of pressure to turn it could be due to a variety of causes. A malfunctioning locking mechanism, misalignment or the wear of the handle are typical causes of this problem.

This is a straightforward and cost-effective fix that a majority of homeowners with double glazing (www.repairmywindowsanddoors.co.uk) can perform. A professional locksmith should be able to solve this problem within an hour after arriving at your residence. Based on your requirements they will be able to replace the locking mechanism, replace the window handles, and also change the gearboxes. A professional locksmith can always advise you on the most cost-effective solutions for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders which give you an extra security layer from burglars. It's a small price to enjoy the peace of mind that comes from knowing that your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks may break. They have intricate mechanisms that become less effective over time. If yours breaks it may be difficult to identify the cause of the issue and make sure you fix it correctly.

Fixing your broken handle, whether it's an internal locking mechanism or latch can increase the security of your uPVC door and stop draughts. It can be expensive to repair or replace your handle if it is not done correctly and can also damage the frame and lock of your door.

Screwdriver Open the window and the screw loose, loosen the handle. The screw should be located on the inside of the backplate, which is usually concealed by a screw cap for aesthetic purposes. Be sure to not lose any internal components within the handle, like the plates or levers that are on the opposite side of the spindle. Ideally, keep these in the same place so you can re-install them when needed.

Then, turn the handle until it's 90 degrees to the window frame and loosen the screw at the back of the handle which holds it to the internal spindle by using another screwdriver. Once this is released, you'll be in a position to pull the handle away and pull out the broken spindle. Replace it with a brand new one, making sure that it is the same length as the previous one (you will typically find them online or in hardware stores) and securely screw it in place. Do not overtighten the screw because this could harm the handle as well as the window frame.

Make sure the new handle is correctly installed after which you can close and test the handle. Hopefully, it will work smoothly and you'll be able open your window again.

Be sure to double-check that your uPVC window is shut correctly while you're working with the handle. If they're not closing correctly, you could encounter damp or draughts in your home. You could also compromise the energy efficiency of your home. A local window company, like Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they can shut properly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is most common in uPVC tilt and turn windows. These windows require a handle that operates a locking mechanism in the window doctor near me frame. The handle is attached to a central rod which is then activated by a series of cams that look like mushrooms, they lock into window frame keeps. If the dead latch mechanism is not able to open after the handle is turned, it is most likely the spindle is damaged. This can be a problem that is frustrating.

There are ways to fix this issue. A skilled locksmith can quickly and effectively fix the issue. A reputable locksmith will be able to disassemble the window's handle using a tool to take out the wheel part that houses the spindle. This can be done without causing any damage to the handle or causing any other damage to the frame of the window.

After removing the wheel the technician can examine the spindle and determine the cause of the break. This involves disassembling the spindle and inspecting each component, noting any wear or damage. The process is carried out in a clean room by highly skilled technicians.

Next, clean the damaged spindle. This will help remove any debris or dirt that could be hindering it from working normally. After that the spindle is cleaned, it can be repaired or replaced. If it's being replaced, the technician could use an identical dowel size to the one used in the first and drill mating holes into both parts of the spindle. This will ensure that the new spindle is an exact fit with the handle.

If the damaged spindle cannot be repaired, it could require replacement. Home centers sell generic replacements but if the design of your window replacement is unusual then you will need to contact a wood worker or cabinet maker who can make the exact part for you. After the spindle is installed, it is connected to the handle. Place the screw holes on the handle with the screws already in the frame. Once the new handle is firmly in place, you'll be able to operate your uPVC window.