Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. They don't get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home and even be fatal. It is important to make sure that your windows are in good condition.

Single-pane windows are fairly simple to replace and typically fit into frames of the past easily. If you have double-paned windows which are held together by internal beading, uPVC repair it is harder to remove and replace the panes that were previously in use. In this situation it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.

If you plan attempt to remove the window panes by yourself it is important to wear the appropriate safety equipment such as gloves that are thick and protective eyewear. It is also recommended to lay down a drop cloth before you begin working on the glass to ensure that any shards will fall on the fabric rather than on the floor where they can be trodden under and cause further damage.

It's a great idea cover the gap with tape after the glass is removed. This will keep water and drafts from entering your home until a professional arrives to repair the window. This will also provide an obstruction to prevent intruders from getting into your home. If the distance between the window and the door is substantial, you may need to consider security screens that includes an opening. This will provide the best of both.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. Over time, they can develop a number of problems, including sliding. A sagging uPVC window can cause issues with light, draughts and even security. If you find that your uPVC window is beginning to sag it's important to act quickly to stop the issue from getting worse.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need to open the window so that you can access the frame. With the screwdriver, you'll be able to take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, shut your window replacement and test it for fitting. If you are happy with the fit of the window, tighten the screws to hold them in the right position.

If you can't reposition the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out, which causes them to lose tightness. It is crucial to replace your seal as quickly as you can to keep your uPVC window waterproof and draughtproof.

UPVC handles can also loosen up. Most often this is due to screws that have come loose over time. However, it can occur because the handle mechanism has been worn out. Luckily, it's not difficult to repair the loose uPVC window handle yourself. First, you'll need close the window and perform an initial test fit. The corners of the sash must be aligned with the casing joint. If it doesn't you can use a screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

If you wake up to damp floors and mouldy walls each time it rains, it's important to take action. Water leaks through windows can cause structural damage to your home and also hinder your ability to control the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

It is a fairly easy fix and should be undertaken by any competent DIYer. Depending on how severe the issue is, the old caulking might need to be removed. When it is time to uPVC repair, you should avoid 'over-caulking'. This will only make your window more difficult to clean and lower its energy efficiency.

Check that any drainage holes are free of debris in them and that the sill pan has been angled correctly to drain away from the window. In more severe cases, you may need to replace the window.

Other indicators of water leakage are decayed sills and the appearance of black spots of mold on the walls near the window doctor. This is a fungus that thrives in damp conditions and can quickly spread throughout the house.

It is also important to note that if the leakage originates from the glass of your double-glazed windows, it is more likely to be an issue with the glass seal rather than the frame or sliding. Again this can easily be fixed by a uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with ease it could be the hinges that are at the fault. They can be easily repaired by any DIYer who is skilled and can be completed in a matter of minutes.

Like any mechanical component hinges are prone to wear out over time. It's easy to change a window hinge however it is simpler if you have someone to help hold the frame.

Check that the uPVC hinges open and close in the right direction. You can do this by looking for the arrows on each hinge. This indicates the direction in which the window should open.

Faulty window hinges could be caused by improperly opening the window a certain way or due to poor installation at the factory. Sending us a photo through our website can often solve the issue. We are happy to offer suggestions.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window open and close more easily. It also decreases the risk of a window sticking and help prevent corrosion. It is recommended to perform this every year. WD40 and other solvent based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a variety of different things. The hinges may also become misaligned due to wear, causing gaps where the sash meets frame. If they are damaged beyond repair, it may be required to realign them. The interlock, which is on the hinge side of the window, can also be misaligned, and again it is feasible to give them a thorough clean, however in certain cases, it may be necessary to have them replaced.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help to regulate indoor temperatures and lessen the risk of draughts.

Lastly, one of the most effective methods to reduce draughts is by using a draught excluder, these are typically made of fabric filled with some sort of filler and Upvc repair can be placed on the top of your windowsill. They can keep your home warm by blocking out cold air.

With a bit of regular maintenance and repairs, your upvc windows will continue to provide an excellent level of insulation and security for your home. It is important to remember that all windows eventually wear out and it may be more cost-effective to replace them rather than repair them. If you encounter any issues with your Upvc window it is recommended to speak with a professional immediately.