Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are durable, long-lasting and easy to maintain. In contrast to aluminium and timber, they don't rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is crucial. This will prevent unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home, and could even be fatal. You should take the time to make sure that your windows are in good shape.

For single pane windows it is fairly easy to replace windows, and the new one is usually able to fit into the frame of the previous one easily. If you have double-paned windows that are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this case, it is necessary to buy plastic spacers to make sure that the new pane fits into the window frame.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the glass to ensure that any shards will fall onto the cloth rather than on the floor where they could be trodden under and cause further damage.

It's a great idea to seal the gap after the glass has been removed. This will stop drafts and water from entering your property until a professional is able to repair the window. It also acts as a barrier that will prevent any intruders from getting access into your home. If the gap between the door and the window is large, you might need to consider an alarm system that has windows. This will give you the best of both.

2. Sagging

uPVC is a durable and energy efficient alternative to timber sash window. However, over time they are susceptible to a range of issues like sagging. A sagging window in uPVC can cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from getting worse.

To fix a Window replacement near me that is sagging you can try repositioning the hinges. First, you'll need to open the windows to get at the frame. With the screwdriver, you'll be able to remove the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and verify the fitting. If you're satisfied with the fit, tighten the screws to ensure they remain in place.

If you are unable to reposition the hinges, you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry which causes their tightness to decrease. If this happens, it's crucial to replace the seal as fast as you can to ensure that your uPVC windows remain watertight and secure from draughts.

uPVC handles could also become loose. This is often caused by screws that have been removed over time, but it can be caused by the handle mechanism wearing out. Fortunately, it's easy to repair a loose uPVC window handle yourself. First, you'll need to shut the window and do an initial fitting. The corner joints of the sash need to be aligned with the casing joint. If it isn't then you can use the screwdriver to loosen the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is crucial to act if you wake up every morning to find a smoky wall and floors that are wet. Windows that leak water do not only lead to the degradation of your home's structure but also hinder your efforts to control the temperature in your home. The most frequent reason for leaking uPVC windows is that the sealant surrounding the frame has been damaged or is missing.

It is a fairly easy fix that can be done by any skilled DIYer. Based on the severity of the problem the caulking that was used up may require removal before a fresh layer can be applied. When it comes to uPVC repair, you must avoid over-caulking. This will only make your window more difficult to clean and reduce its energy efficiency.

It is crucial to make sure that any drainage holes are free of debris and that the sill pan has been angled correctly so that it drains away from the window. In more serious instances, you may need to replace the window.

Other indicators of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window. The mold thrives in damp environments and is able to quickly spread throughout the house.

It is also important to note that if the leakage originates from the glass of your double glazing glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. A uPVC specialist can easily solve this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and open with a breeze it could be hinges that are at fault. These are easily repaired by any DIYer who is skilled and can usually be done within a few minutes.

Almost every household in the UK will have either top hung or side-hung uPVC windows that use hinges and like any mechanical part they will wear out over time. It is very easy to change the hinges on a window but it's much simpler if you have someone to help you hold the frame.

It is also important to ensure that the uPVC hinges are being opened and closed in the right direction. You can check this by checking for the arrows on each hinge. This indicates the direction in which the window should open.

The issue could be caused by opening the window improperly or due to a poor installation in the factory. Sending us a picture via our website will often resolve the problem. We are more than happy to give suggestions.

Regularly lubricating hinges is also essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window to operate and close more smoothly. It can also stop corrosion and reduce the possibility of sticking. It is recommended to perform this every year. WD40 or other solvent-based oils should not be used since they could damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. First, the hinges because of wear and tear, may become displaced, which causes gaps to develop where the sash joins the frame. If they are beyond repair, it might be required to realign them. The second is the interlock, which is on the hinge side of the window and Window Replacement Near Me can also be misaligned, and again it is possible to give them a good clean, but in some cases it might be necessary to get them replaced.

These seals can wear down or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping can help stop draughts. Replace the windows made of Upvc with low-emissivity glass. This will help control indoor temperatures, and reduce the possibility of draughts.

Lastly, one of the most effective ways to reduce the draughts in your home is to use a draught excluder. These are typically fabric tubes which are filled with a type of filler. They can be placed on the top of your windowsill. They will keep your home warm by blocking cold air.

With a bit of regular maintenance and repair windows made of upvc will provide excellent insulation and security for your home. It is crucial to keep in mind that all windows eventually wear out and it is more cost-effective to simply replace them than to repair them. If you encounter any issues with your window made of upvc, it's best to consult an expert as soon as possible.