Reasons Why Your nissan qashqai key (Get Source) Fob Won't Work

The Qashqai's bigger dimensions give it an SUV feel. Its 19-inch alloy wheels in Ti and STL versions may also be firm. The front tyres in the Qashqai could also lose grip on rough surfaces and its CVT can occasionally display a wrist-flexing torque steering.

This is typically caused by a dead coin battery which can be easily replaced in minutes. Make sure the replacement battery is of the same voltage, size and specification.

Water Damage

One of the main reasons that a Nissan key fob gives the "key ID is not correct" message is due to water damage. The key fob is fitted with rubber seals that protect the chip inside, but prolonged exposure to moisture could cause it to stop working properly. It's common to see this happen if your key fob was dropped into the ocean or in a pool. However, it could also occur when it's wet from showers or soapy hands.

If your key fob has been exposed to water for a long period of time, it could need to be cleaned with isopropyl ethanol or electronic cleaner. In addition, it may require taking to a professional for repair or replacement.

If your key fob requires to be replaced, it's an easy process. First, make sure you have a multipack with the correct battery (CR2032 3V). Remove the front and back cases with the flat-head screwdriver. It is necessary to remove the clips for retaining metal and pull out the old battery, and then replace it with the new one. Reassemble the fob and replace the mechanical key. Make sure it's working properly. If it doesn't, you will need to take it to a local Nissan dealer or an experienced auto locksmith to fix the chip in the key. The chip is usually not damaged by water and therefore isn't too costly.

Dead Coin Battery

The coin battery is another frequent reason why your Nissan Qashqai remote key fob won't work. The batteries last for about 3 to 5 years, but they are prone to failure over time in the event that the fob has been dropped frequently. You could replace the battery but ensure it's the same voltage and the same size as the previous. If you install a new battery, it could cause the key to be assigned an incorrect key ID. This will prevent it from being linked to your vehicle.

The best way to replace the coin battery on the nissan juke key replacement Qashqai key fob is by prying open the key fob using the small screwdriver with a flat-head. The screwdriver must be inserted into a small cut on the bottom of your key fob. The screwdriver should be gently twisted to separate the two halves. Then, take out the old CR2025 button cell battery and replace it with a new one after noting its position in the fob.

Before you put the new battery in place check to ensure there isn't any dirt or water damage on the terminals. If there is, wash the terminals using a small amount of isopropyl alcohol. You'll also want to ensure that the pole cables are plugged in correctly. They should be connected to the negative and positive poles of the battery.

Diagnostics of a fault

If your Nissan Qashqai key fob stops working after exposure to clean rain or tap water it could be an indication of an internal chip problem. You'll need a new keyfob in the event that you can't resolve the issue by replacing the battery. If you dropped the key fob on the ground and it stopped functioning immediately it's likely because it has damaged the internal chip. You can usually get the key fob back to function again if you take it out and clean the chip with alcohol and paper towels and then put it back in.

One common error you may notice on your car's dashboard is "Key ID Not Correct." This means that the vehicle cannot recognize the key fob and not allow it to start the engine. The issue could be caused by a variety of things like water damage, undetectable malfunctions in the circuitry of the key fob, or RFID interference.

The key fob will cease to function if the 12 volt batteries are not working or provide enough electric current. This can affect the remote keyless system and central locking in your Nissan Qashqai, as well as hindering you from starting the engine using the key fob (if equipped with Intelligent Key). If you can't unlock or lock the door by hand it is recommended to check the batteries inside your key fob to make sure they are in good shape. You could also try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob is not been submerged in salt water and is unable to come back to life after a quick wash with clean water. You can also try cleaning the electronic chip using isopropyl alcohol or an electronic cleaner. If none of these work It could be the time to replace the entire key fob with a brand new one.

If your Nissan Intelligent Key is still not working, there could be a problem with the connection between it and the car. To reconnect it, begin by turning the key into the ignition, but not starting the car. Continue to do this until you see the warning lights flash twice. Turn the vehicle off and take away the keys.

Then, you must open the fob compartment inside your vehicle. It's usually located in the door jamb, on the handle for the driver's door or under the armrest. Find the small "program" button and press it. After the program is complete, you should hear the sound of a chime.

Now that your Intelligent Key is relinked to the car is the time to test it out. Set your feet a distance from the car, and hit all the buttons on the key. If the lights flash, or the horn sounds, the key is connected to the Nissan. You can also test it near the Nissan.