How to Replace a Kia Sportage Replacement Key

The key of many Kia models comes with an electronic keyless entry system built into. This key usually resembles a remote control and can be exchanged with a brand new one from a Kia dealer or locksmith.

Key fobs may stop working for a variety of reasons, such as batteries that are dead worn buttons signal interference, water damage and a faulty receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How do you replace the remote key or smartkey?

Whether your Kia comes with an intelligent key, remote key, push to start key or regular metal non-transponder key the battery in these keys will eventually need replacing. This is particularly when the car displays a message indicating that the remote or smart key is not powered by the battery.

Fortunately, it's quite simple to do. To replace the key fob battery, remove the mechanical key from the hole in the back of the key fob. You then need to lift the cover. Inside the key fob there will be an incredibly small screw that holds the battery in place. Remove the old battery by unscrewing the screw with the help of a small screwdriver. Install the new battery and then close the opening on the key fob.

Once the key fob has a fresh battery Test it by pressing the locks and unlock buttons. If the doors unlock and lock according to your expectations, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a programming machine that is only available to the automotive locksmith or dealer. Other keys (non transponder metal keys), do not need programming. If your key needs to be reprogrammed, you must know the key code number that is stamped on the tag of the key code and record the number in a secure place.

How do you replace the battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light appearing or the engine not cranking properly. Fortunately, replacing the battery on the key fob is a fairly simple DIY task that requires only a few tools.

Make sure to shut off your vehicle and shut all doors prior to starting. Find the small, metal or plastic piece at the bottom of your key fob and gently jiggle it until the metal key slips out. This key can be put into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover from the back and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and then orient the new battery so that the "+" positive side faces you and the "negative" negative side is facing the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.

Once the new battery has been installed, turn the key fob off and then on in the ignition repeatedly until the door locks cycle. Then you can test your kia duplicate key key fob and see if it is working properly again.

How do you replace a smart keys

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between these is that the smart key is equipped with the small blade of a key tucked inside it, while the standard fob doesn't. Both key fobs come with batteries that will eventually require changing. Fortunately, it's an easy task that only takes about two minutes.

Be sure to switch off your kia sportage Key and stand on a level, well-lit surface before you begin. Also, keep in mind that there are tiny parts inside the fob that could fall out if you are not vigilant.

The first step is to locate the small release button that is located on the backside of the fob. It will be either a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, take out the old battery. The new battery is a the CR-2032, and it can be purchased through the internet or at a local auto parts shop. After installation it should be possible to lock or unlock your vehicle with your key fob, even if your engine isn't running!

How to replace a mechanical key

The Kia key fob is an amazing feature that lets us lock and unlock our car at the click of an button. But like any device it may have issues from time to time. There are ways to resolve these issues and keep your key fobs running for many years.

One of the most common problems is a low or dead battery. This can cause the fob to stop working entirely or work intermittently. If this is the problem, replace the battery with a new one.

If this isn't enough to solve the problem, use the flathead screwdriver that is standard to wedge the plastic casing of the fob open. Be cautious not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a new one.

Once the new battery is in, close and then open the doors using the mechanical key (every key fob in the kia has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's working correctly. If the fob isn't working, call an expert locksmith or dealer to help resolve the issue. To avoid future lockouts, make sure you get an emergency key that will work on all trunk and door cylinders.