Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. They do not decay or rust as aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause significant damage to your home and may even be fatal. It is essential to take the time to ensure that you're doing all you can to keep your windows in good repair.

Single-pane windows are relatively simple to replace, and they will usually fit into the old frames very easily. However, if windows with double panes are secured by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this instance, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric, not onto the floor which could cause them to be trampled.

Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent water and drafts from getting into the property until a professional is able to come out and fix the window. It also acts as an obstruction to prevent intruders from getting into your home. If the distance between the door and the window is substantial, you may want to use an alarm system that has an opening. This will give you the best of both.

2. Sagging

Upvc is a long-lasting and energy efficient alternative to timber sash windows. In time, they could be affected by a variety of issues such as sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from worsening.

To fix a sagging window you can try to reposition the hinges. First, you'll need to open the windows so you can access the frame. With an screwdriver, take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. Close your window doctor near me to check the fit after having relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure they stay in the right place.

If you aren't able to move the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, causing them to lose their tightness. It is important to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles could also loosen. Often it is due to screws that have become loose over time. However, it could also happen because the handle mechanism has been worn out. Luckily, it's not difficult to repair the handle of a window that is loose yourself. First, you'll need to shut the window and do a test fitting. The joint at the corner of the sash should align with the joint on the casing. If it isn't, you can use the screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is important to act if you awake each day to find a smoky wall and wet floors. Water leaks through windows can cause structural damage to your home and also hinder your ability to control the temperature in your home. The most frequent reason for leaks in uPVC windows is that the sealant around the frame is damaged or not present.

This is a fairly simple fix and should be undertaken by any skilled DIYer. Depending on how serious the issue is, the old caulking may have to be removed. When it is time to uPVC repair, you should avoid 'over-caulking'. This will make your window more difficult to clean and decrease its energy efficiency.

Verify that the drainage holes do not have debris in them and UPVC repair that the sill pan is angled correctly to drain away from the window. In more severe instances, you may need to replace the window.

Moldy sills and rotten ones are other signs of water leakage. The is a fungus that thrives in damp conditions and is able to quickly spread throughout the house.

It is also important to note that if the leakage originates from the glass of your double-glazed windows, uPVC repair it is more likely to be an issue with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open in a breeze It could be hinges at fault. These are easily replaced by any competent DIYer and are usually completed in a matter of minutes.

Almost every household in the UK will have either top hung or side hung uPVC windows that have hinges and, just like any mechanical component they are susceptible to wear and tear over time. It's easy to change the hinges on a window but it's much easier if someone helps you to hold the frame.

Make sure that the uPVC hinges open and close in the right direction. This can be done by looking for the arrows on each hinge, this indicates the direction in which the window should open.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a certain manner or because of poor installation at the factory. Sending us a photo via our website is often enough to resolve the problem. We are always happy to offer advice.

It is also important to ensure that the hinges are lubricated on a regular basis. Applying an engineering lubricant that is light to the hinges is a great way to do this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also prevent corrosion and decrease the chance of sticking. This must be done at a minimum once a year. WD40 or other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a few various factors. The hinges can also become misaligned due to wear, causing an opening between the frame and sash. These can be easily repaired by giving them good clean, but in the event that they are beyond repair it might be necessary to have them realigned or replaced. Secondly the interlock, this is on the hinge side of the window, may also be misaligned, and again it's feasible to give them a good clean, but in certain cases, it may be necessary to have these replaced.

The second most frequent cause of draughts is the window seals. They can become worn down or damaged over time and allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help control indoor temperatures, and reduce draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler, which can be put on top of your window sill. These will help to keep cold air out and keep your home warm and cozy!

With a little regular maintenance and repair windows made of upvc will continue to provide a great level of security and insulation for your home. It is crucial to keep in mind that all windows will eventually get worn out and it may be more cost-effective to replace them instead of fixing them. If you are experiencing issues with your Upvc windows, it is recommended to seek help from a professional as soon as you can.