Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and know-how. They can create and program keys faster and cheaper than a dealership.

A dead coin battery is the most likely cause if your key fob stops locking or unlocking the doors. There are other reasons that the key might be malfunctioning.

Dead Coin Battery

A dead battery can stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. If this is the case, you'll have to utilize the backup starting method that is described in the owner's manual of your vehicle.

The spark plugs could also be worn out. The spark plugs are responsible to ignite the fuel that ignites the engine. However they have a short life span. They'll eventually degrade if they aren't used frequently enough.

There is a simple solution for this issue. The best thing to do is to test the voltage of your car battery using a multimeter. If the voltage is less than 11,5 volts, it's the time to replace it. It is also essential to clean the contacts of the battery in case it is corroded. This can be accomplished by removing the rubber covers off the two battery terminals, and then using a wirebrush, you can remove any corroded battery parts. Then, you must reconnect the positive and negative pole cables.

Water Damage

If your 208 won't turn on and the battery is not flat then you should check whether the spark plugs are in good working order. It is possible that they are overly dirty, which causes them not to spark. The spark plugs can be cleaned in a workshop.

Peugeot 308 Key fob automobiles use a transponder key that works with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't send the proper signal to the vehicle.

Water damage is a typical cause of this problem. This is a common issue in areas with colder temperatures where the vehicle is exposed to rain or snow. In this situation, contact a trusted locksmith who will have the tools and equipment needed to modify the key. They will also have the latest technological know-how and the equipment required to create the Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts of the battery may be damaged.

Peugeot changed from the old carbon encased transponder chips to an entirely new kind of chip that utilizes electronic components within circuit boards. This new system works well when it's brand new, however, over time, the circuit boards begin to wear out and stop functioning correctly.

This could stop the immobiliser chip from activating the immobiliser chip, causing your car not to start. Contact an Peugeot specialist or a locksmith, if this is the case.

Another issue that is common is when the battery for the key fob starts to die, this causes the blade of the key to stop feeding into the lock. A locksmith in your car can replace the battery and cut a new blade for you, this is typically a quick fix.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it may be due to a defective receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which manages the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals that block water from getting to the electronic chip inside. The chip can be damaged by water if it is exposed to water for a prolonged period of time. Submerging the key fob in ocean water on the beach or throwing it into the water can be particularly damaging due to the high salt content.

The module will have to be replaced if your Peugeot spare key does not work anymore. This is only performed by a professional auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the correct programming to start the engine. This is the reason that you should only rely on the Peugeot locksmith to create and program the replacement.

Faulty On-Board Computer

The computer on board of your Peugeot is responsible for various systems inside your car, including power windows and airbags. When something goes wrong in these systems, they will usually show a code that identifies the issue. The code is stored within the system and will stay there until the problem is resolved. In most cases, this will require replacing the onboard computer.

One of the main reasons for the light flashing is loose or corroded connection in the airbag sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. It is essential to have this issue addressed as quickly as you can, since an airbag that is not functioning properly could be dangerous in the event an accident.

If you find an error message stating that the card is not found on your Peugeot, the key battery inside the key fob could be dead or weak. This will prevent the key fob from sending a signal to disable your vehicle's immobilizer. Try this by pressing the unlock button on the fob's key and then trying to start your vehicle. If it doesn't work then the battery in the key fob is in need of replacement.