How to Replace a Kia Sportage Replacement Key

The key on many kia key Replacement models comes with a keyless entry system built in. The key functions like an remote control, and is exchangeable by a Kia dealer.

Key fobs might stop working due to a variety of reasons, such as a dead battery, worn-out buttons signals, signal interference or water damage. Here are some suggestions to help you get your kia ceed key fob sportage replacement key to work for good.

How do you replace a smartkey or remote key?

If your Kia comes with an intelligent key, remote key push-to-start key, or a standard non-transponder key made of metal, the battery in these keys will eventually need replacement. This is particularly when the car displays a message telling that the remote or smart key has low battery power.

This is a relatively simple process. To replace the key fob battery, remove the mechanical key from the slit on the back of the key fob. Then remove the cover. Inside the key fob, there will be the small screw that holds the battery in the correct position. By using a small screwdriver take the screw off and remove the battery that was in place. Install the new battery and then close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go when the doors lock or unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you need to complete errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you need to reprogramme your key, you'll need to note the key code's number on the tag for the key code.

How to replace the battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery should be replaced. A weak battery can cause other problems like the check engine light coming on or a delay in cranking the engine. Fortunately replacing the key fob battery is a simple DIY project that requires just a few basic tools.

Before you begin before beginning the process, ensure that your vehicle is off and that all doors are closed. Find the small, metal or plastic piece at the bottom of your key fob and jiggle it until a metal key slides out. Then, you can insert the key in the door handle of the driver to open your car.

To replace the key fob battery, remove the cover from the back and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery and align the new battery in a way that the "+" positive side is facing you, and the "-" negative side is facing the fob's metallic electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or breaking the metal contacts.

Once the new battery is installed, turn the key fob off and on in the ignition for a few times until the door locks. Then, test your Kia key fob to check whether it's working again.

How do I replace a smart keys

Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The difference between the two is that the smart key has the small blade of a key hidden within it, whereas the standard fob isn't equipped with. Both types of key fobs have batteries inside that eventually will need to be replaced. This is a straightforward process that takes only two minutes.

Be sure to switch off your Kia and stand on a flat or well-lit surface prior to when you begin. Remember that the fob can contain small parts that can fall if you're not careful.

The first step is to find the small release button on the backside of the fob. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been open, remove the battery that was in it. The new battery is one called CR-2032 and can be bought on the internet or at your local auto parts shop. After you've finished with the battery, you should be able to lock or unlock your vehicle with your key fob even if the engine isn't running!

How to replace a mechanical key

The Kia key fob is a great option that lets us lock and unlock our vehicle with the click of a button. But, as with all devices, it can have problems at times. There are solutions to resolve these issues and keep your key fobs working for a long time.

One of the most common problems is a dead or dead battery. This can cause the fob to stop working entirely or even to stop working intermittently. If this happens you should replace the battery with a new one.

If this doesn't fix the problem, try using a standard flat-head screwdriver to break open the fob's plastic casing. Be cautious not to damage any internal components or scratch the plastic. Once the battery is removed and replaced with a new one.

After the new battery has been put in, close and open the doors using the mechanical key (every kia car key replacement fob has an emergency mechanical key that will fit into the slot). Test the key fob to verify that it's functioning properly. Contact a dealer or a locksmith to resolve the problem when the fob still is not working. To avoid a lockout in the future ensure you purchase an emergency key that will be able to work with all trunk and door cylinders.