Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai's bigger dimensions give it an SUV-like ambiance. Its ride on 19-inch alloy wheels on Ti and STL models can also be a bit firm. The front tyres on the Qashqai may also lose grip on rough surfaces and its CVT can sometimes display a wrist-flexing torque steering.

It is usually due to a dead battery, which can be replaced in a matter of minutes. Be sure that the replacement battery is the same voltage, size, and specification.

Water Damage

One of the main reasons that a Nissan key fob will give the "key ID is not correct" message is due to water damage. The key fob has rubber seals that protect the chip inside, but long-term exposure to moisture could cause it to cease functioning properly. It's common to see this if your keyfob was dropped in the ocean or in a pool. But it can also occur when it becomes wet due to rain or soapy hand.

If your key fob was exposed to water for the course of a long time, you may need to clean it with isopropyl or electronic cleaner. Alternatively, it might need to be taken to an expert to repair or replace it.

If your key fob needs to be replaced, it's a relatively simple procedure. Make sure you have the correct multipack (CR2032 3V). Unlock the front and rear cases using the flat-head screwdriver. You'll need to take out the clips that hold the metal together and push out the old battery, then put in the new nissan key one. After reassembling your fob, put the mechanical key back into its place and make sure it operates correctly. If it does not then you'll need to take it to a local Nissan dealer or an experienced locksmith to replace the chip that controls the key. The chip is usually not damaged by water and therefore shouldn't be too expensive.

Dead Coin Battery

Another reason that the reason your nissan key replacement prices Qashqai key fob may not work is that the battery in the coin has gone dead. These batteries last for three to five years, however they are prone to failure over time in the event that the fob has been frequentedly dropped. You can replace the battery, but ensure it's the same voltage and the same size as the first. If you replace the battery, it may cause the key to be assigned a wrong key ID. This could prevent it from being linked to your vehicle.

The best way to change the battery on the Nissan Qashqai Key Fob is to break it open using an incredibly small screwdriver. The screwdriver should be inserted into a small notch on the bottom of the key fob. Simply twist the screwdriver to divide the two halves. Then, take out the old CR2025 button cell battery and replace it with another one after confirming its location on the fob.

Before you put the new nissan key battery into place be sure that there is no dirt or water damage on the terminals. If there is, clean the terminals with a small amount of isopropyl alcohol. You'll also need to make sure the pole cables are connected correctly. They should be connected to the positive and negative poles of the battery.

Troubleshooting

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be a sign of a chip issue inside. You'll require a new keyfob if you can't solve the issue by changing the battery. If the key fob stopped working after you dropped it, it is likely that the chip inside was damaged. If you clean the chip using isopropyl ethanol and a paper towel and then insert it into the key fob, you'll generally get it back to working.

A common error that you might see on the dashboard of your car is "Key ID Incorrect." The car is unable to recognize the key fob, and consequently, won't allow the car to start. The issue can be caused by a variety of things including water damage, undetectable issues in the circuitry of the key fob, or RFID interference.

If the battery that powers 12 volts on your key fob is inactive or is not supplying enough electric power, it will stop working. This will affect the remote keyless system as well as central locking in your Nissan Qashqai, as well as hindering you from starting the engine using the key fob (if equipped with Intelligent Key). Examine the batteries on the key fob if you're not able to lock or unlock your door manually. Try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged into saltwater, it should be able be restored to its original state with a simple rinse of clean water. You can also clean the electronic chip using isopropyl or electronic cleaner. If none of these work, you may have to replace the key fob.

If your Nissan Intelligent Key is still not working, there could be an issue with the connection between it and your car. To relink it, start by turning the key into the ignition without starting the car. Continue this process until the hazard light blinks twice. Then, turn the car off and take the keys out.

Next, open the fob compartment of your vehicle. It is typically located in the door jamb, on the handle of the driver's side or under an armrest. Find the small "program" button and press it. Once the process is completed you will hear an emitted sound.

It's time to put your Intelligent Key to the test. Click all the buttons on the key while standing at a distance from the vehicle. If the lights flash or the horn sounds, then the key is successfully connected to the Nissan. You may also try testing it in close proximity.