Reasons Your fiat 500 key replacement cost 500 Key Fob Won't Work

A key fob from fiat 500 replacement key fob 500 is a great way to unlock the doors and start the car. There are a myriad of reasons the fob could stop working. It could be due to a dead battery, damage to the receiver module, water problems, and interference.

This listing is for a NEW replacement Fiat Key Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob being inoperative. Modern key fobs come with a limited operating range, and should be within a few feet of the vehicle to operate. If you're far from your vehicle and you press the key fob button, the car won't be able to respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery on your coin cell (Part number CR2032) by a new one from a trusted brand like Panasonic, Duracell, or Energizer. You can find them at the local hardware store or online.

After you've changed the battery on the coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The parking lights should flash and the key fob will operate the lock and unlock switches.

If your key fob isn't working after replacing the battery, it may be water damage that has prevented it from connecting to the module in your vehicle. Water damage can happen in a variety of ways, such as a simple splash or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, try placing it in a dry rice bag to pull the moisture back out. If this doesn't work your fob is likely to need to be reset by a professional auto locksmith or the dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean, or wash it in a washer. Saltwater poses a particular risk to the fob's circuit board that can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not a good idea but if you drop it into a cup of water or forget to remove it from your pocket before you run the washer do not give up hope.

Remove the battery first. Clean the electronic chip with isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Test the fob afterward to determine if it's working. If the key does not work, it may need to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is a bit older and is not programmed for your car, you will need to replace it completely. A professional locksmith for cars can do this job. The locksmith will require the key cut to match the car's ignition. The locksmith will also need to reprogram the fob into the car's system. This is a simple and affordable process which can be completed within the next day.

Receiver Module Issues

Your 500 key fob may stop working because it is out of range. The remote typically has an area of 30 feet or less, and if it's too far away from your car it won't respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If your fob does not work after replacing the battery inside the coin, which is also called a "button", "watch" or "button" or "button", it could be a problem with the circuit board inside. In the majority of cases, reprogramming your fob will fix the issue. There are instructions on how to do this for the majority of automobiles by searching YouTube or looking through the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they lose tension, it can prevent the coin battery from sitting properly, and this will cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle because of software or hardware issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases it may be necessary to install the software again in your body control module as well.

Interference

Interference can also cause the key fob to not be able to receive or transmit an signal. This could occur if the keyfob is in close proximity to a radio transmitter such as a cell phone or radar detector. The key fob might not function because of a weak connection to the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a malfunctioning receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then read by the vehicle.

There's a quick and easy way to reset the 500's internal system, including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electric current, and also restart the car's computer. This could help you get your key fob to function again. If the issue continues you should speak with an expert certified technician. They'll be able identify the root cause of your problems.