Replacement Upvc Window Handles

The majority of replacement windows window handles made of upvc include everything you require to complete the task. However, if the old handle had pins or screws holding it, these will need to be removed. Take off the "snap-in" cover at the base of your handle.

The next step is to determine what kind of window and lock your new handle for - this is crucial!

Espag

Espag handles are a type of multipoint locks that are fitted to casement window types like uPVC or wooden double glazing. They have seven millimetre square spindles that fits into the gearbox on a uPVC window and when the handle is turned, it triggers with a series of locks that run around the perimeter of the window. Espag handles are also referred to as shootbolt handles. They provide extra security compared to the typical single point lock that is found on older window frames.

There are many options available, including inline and cranked handles that can be operated by either the right or left hand. You can also find ergonomic handles that enhance the appearance and feel of your window, as well as handles.

You'll need to determine the spindle size from the base of your uPVC handle in order to order the correct replacement. This measurement is known as step height and will assist you in finding the ideal uPVC handle for your home.

If you require to remove any screws that secure the handle, you can use pliers or a screwdriver. Once you have done this then you must disassemble the handle by taking off the screws or pins that hold the spindle and then pulling it away from the window.

After you have removed the handle, you will be able to access the locking mechanism within the frame of the windows. You can then remove the cockspur block that is located next to the handle. This will allow the window to be opened. The new uPVC window handles you have purchased should be able to fit on the wedge block of the cockspur and then into the handle spindle and allow the window to open once again. Ideally, you should replace the cockspur wedge block with an entirely new one when you change your uPVC handle to ensure it is properly secured.

Cockspur

Cockspur handles are found on older uPVC or aluminum windows. The handle rotates and closes over an aluminum wedge-shaped receiver catch (not to be confused with window latches made from timber which are also handled in this section). The handles are available in lockable and nonlockable models. They are available in different nose heights that can be adjusted to the existing frame.

The handle is locked by a small triangle-shaped spur (spur) that is attached to the frame. These are usually one-way handles, but a deadlock with a locking mechanism is a possibility to add additional security.

As with Espag handles, replacement handles for cockspur handles are simple to install, all you need is new screws (supplied) and the proper backset. The backset is measured from the baseplate to the underside nose of the handle. As a general rule Aluminium window frames tend to have a backset of 9mm, whereas UPVC utilizes 21mm. There are a myriad of variations however it is essential to take a measurement before buying the handle (see the video below for more details on how).

The spindle, or in some cases, the entire handle assembly is removed by unwinding the handle. The replacement handle can then be secured with a pair of pozidriv screws. The pozidriv screw comes in a brass or a zinc finish, to match existing hardware. There is also an option for self-locking pozidriv screws.

This is an easy to install replacement for the cockspur handle that is perfect for fixing or replacing old uPVC windows, they have a universal design which makes them suitable for a variety of profiles and backsets. Each handle is supplied with 3 packers that vary in thickness. They are fitted to the underside of the handle's nose and can be arranged in a variety of ways to achieve backsets of 9-13mm, 17mm and 21mm. They are available in left and right handed models and are available with lockable or nonlockable models with a choice of nose heights.

Tilt and turn

Tilt and turn windows are a coveted European window design that has been around for decades in Europe, but is only getting noticed stateside. The windows are a combination of 3 window styles - tilt, in-swing and pivot. They are great for older homes because they are more breathable than conventional windows.

When tilt and turn windows are closed, they will lock as any other fixed window. By turning the handle either 90or 180 degrees, based on the tilt-and-turn type of window the sash opens inwards, and the window will turn inward to allow air exchange. This is a great way to allow air circulation without having to open an enormous potentially dangerous window.

If the handle is turned another 90@ or 180@ the sash will be fully opened like the door. This allows for full air exchange which is especially useful for draughty houses or rooms where smoke or other smells can build up. It also makes cleaning the outside of the glass window replacement much simpler because it can be done from inside the home - a job that usually requires ladders that are a bit shaky.

Tilt and turn windows are also extremely secure. They are very difficult to open when locked in the closed position. They also have double seals which stop rainwater from entering your home while in the tilted position or in swing. This feature is particularly useful for older homes, where burglars tend to target windows that can be opened using side hinges.

Spade

There are many different kinds of handles that are able to be fitted on upvc double-glazed windows. The two main kinds are Espag handles and Cockspur handles. There are also tilt and turn handles blade or spade handles, Replacement Upvc Window Handles and monkey tail handles. The type of handle you choose will depend upon your preferences as well as the type of windows you have.

In order to choose the correct replacement for your window handle, you need to know how your current handle is attached to the frame. This is known as handing and is a crucial piece of information, especially when purchasing online since some handle variations don't fit all windows. Certain cockspur handles, as an instance, are angled whereas others are straight and can turn either left or right. You should also be aware of what the spindle length is, which is the distance from the base of the handle to the top of the handle.

Another aspect to consider when choosing the right handle is determining whether your windows need a restrictor or not. These are typically found in high rise flats or commercial buildings, but they're not a requirement for the majority of homes. It is also important to be aware of the step height which is the distance between the screw plate and the nose of the handle.

Spade is a word that comes from Old English spadu or spaedu and has been translated into various languages including German spaten and Low German Spathen. During the Harlem Renaissance of the 1920s in New York City the word spade was used to mock black people. Spade has since risen to prominence in pop culture and is a widely recognized symbol of African American heritage and pride.

When replacing the handle of a Cadenza handle, it's essential that you get the right size. Handles are available in straight and angled versions that differ by just a few millimeters. The handle head is available in a variety shapes that include a D or T shape. It is also possible to be left unhandled.