How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have to follow a series of special steps to install an additional ignition key. This requires a handheld computer, called Tech-2 which is used by the dealer. Then a new car key and transponder are required to be purchased and then programmed into the car.

Change your keys regularly to prevent one from wearing out more than the other. This will also ensure that your keys remain in top condition.

Replacement Case

The new key fobs aren't like the older Saab keys. They feature electronic components that make it difficult to copy. This has made theft of cars considerably more difficult than it was years ago. It has also made it more expensive to replace keys lost.

Saab 9-3 owners should have two working keys. It costs a fortune to replace a lost key because it requires replacing the CIM module, as well as programming the locking cylinders. Dealers will typically charge $100-$200 to do this.

There are several ways to get around these expensive. Some parts providers will use the code of an old key to cut a brand new metal blade for less than the cost of the dealer. The key, however, must be identical to the original in order to function in your car.

Follow these steps to replace the case. You'll need a flathead screwdriver along with some patience. With the screwdriver, slowly pry the plastic apart and remove the emergency key from the case. Once the case has been opened, remove all electronics and put them back in the new case. Make sure you insert the correct key and [empty] badge back inside the case, too.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost part that can be replaced quickly and easily. This video tutorial on DIY from YouTube Cyclone Cyd will show you how to replace the remote key fob battery in only four steps. This tutorial will work with any modern saab car keys key fob. However, the process might differ slightly.

The first step is to locate the button that will release the backup key within the fob. This button is usually located next to the Saab logo on the back of the fob. Use a flathead to insert the screwdriver through the small hole in this button. This should be enough to let the fob case open in order to change the battery.

After the new battery CR1632 is in place it is possible to reassemble the remote key fob. You can then program it to your car. The whole process should not be more than an hour. It is a simple process that does not require any special equipment.

If you lose a key the process will be a bit more involved but it is still able to be accomplished. The dealer needs to first determine the VIN of the vehicle and order an additional TWICE module and key blade with the proper unique code. After that, they will need to cut the replacement key and then program it using a new software tool called MDI.

Replacement Key Fob

The key fob is the device that locks and unlocks your car. It has batteries inside. Batteries are able to last for a short time and eventually die. This is a typical issue that happens with all cars and the good thing is that you can change the batteries in most fobs, without replacing the entire case. You can buy replacement fobs from Amazon that have all the electronics already installed, so you can just pop open the case and replace those batteries that are old. You'll need to remove the emergency key before you replace the batteries. To accomplish this, simply insert a small screwdriver that is flat into the slot that is in the middle. Work the screwdriver around the case until it is split open, making it easier to remove.

If you're ready to replace your keys, keep a spare available. This will save you a significant amount of money. If you have an additional key, you can request the dealer to cut it in half and program it to your vehicle. This is much less expensive than buying a new key fob.

If you don't have a spare car key, you can add an additional key to your car, however it requires a lot of research and effort. The cost for adding a second key is a few hundred dollars, and it requires programming of the car's computer. Professionals can accomplish this however it's a costly option.

Replacement Ignition

Contrary to earlier saab 9 3 key replacement cars, the modern SAAB 9-3 models have an extremely sophisticated alarm system that is built on a key code. This means that in the event that you lose your only working key, acquiring an additional one could be extremely expensive since the car has to have a special computer module added and it also needs to be specifically designed to accept a different key. The majority of locksmiths aren't able to do this, and even a dealer will charge several hundred dollars to program the new key!

If you've lost the only working key and a dealer is able to replace the computer in your car (known as the CIM or SAAB TWICE) in order to make the replacement, and will charge a premium for it. Instead we can reprogram the EEPROM on your existing car computer to prepare it for a new key, saving you over 50% of what you'll have to pay at a dealership.

If you've been an owner of an 03-11 SAAB 9-3, then you probably have noticed that the ignition switch isn't the most durable. They can become extremely sticky, [Redirect-302] and the buttons can be ripped off occasionally It is recommended that you consider replacing your ignition key if it isn't functioning properly. The good news is that replacing the ignition key isn't as complicated as it seems, and it can be done fairly quickly with the right tools.