UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a simple process and with the right tools it can be accomplished quite quickly. It is important to know the type of handle you have and its spindle size before purchasing a replacement.

Older uPVC windows use cockspur window handles which have a spur that protrudes to secure a wedge-shaped cockspur striker plate. They can be left- or right-handed and should match when replaced.

What kind of lock and handle do I have?

There are a variety of upvc window handles and locks, each with their distinct advantages and functions. The type of handle that you own will determine if your locking mechanism is effective and if it's easy to open the windows. As time passes, and with regular use the upvc handles that are on your windows could become damaged and worn out. This makes them less secure and effective. In some cases they may even fall completely off. If you notice that your upvc double glazing window replacement handles have been removed, it's important to repair them as quickly as you can. This will stop possible burglaries and will keep your home secure.

Luckily, replacing your window handles made of upvc is a relatively simple task that is achievable by nearly everyone. You will need a few tools, but with right knowledge, it is simple and should only take a couple of minutes. You will need to be aware of the type of lock or handle you have on your window. This will help you select the right replacement.

Inline Espagnolette Handles

These are the most commonly used kind of upvc handle and are usually placed on the outside of your window. They are flat and feature an opening that engages the locking mechanism of the window frame. Inline upvc handles also have a spindle that runs through the middle of the handle, and into the frame of the window to operate the latch.

Cockspur Handles

They are usually found on older uPVC windows and feature a distinctive hook-shaped design. Cockspur handles have one screw that is used to secure the handle to the frame of the window and UPVC Window Handle Replacement are not as secure as other kinds of window handles.

Handles that can tilt and turn

The tilt and turn handles differ from other handles made of upvc in that they can be turned to open the window and then tilted into the window to allow air circulation. They have a 7mm spindle on the back and are available both in right-hand and left-hand versions.

When purchasing replacement handles made of upvc, it is important to verify the length of the spindle because not all handles are the same size. Drop something in the middle of the hole to measure the length. This is the maximum spindle size that will fit in your windows.

What is spindles?

uPVC window handles operate similarly like doors, turning the handle to operate a latch inside the frame. The window is then opened and closed. However, sometimes handles can be damaged, especially when they are used frequently or exposed to harsh weather conditions. This can lead to the need to replace your uPVC handles on windows since they may not be able to operate the window correctly in the future.

There are many different kinds of uPVC handles available comprising Espag, Cockspur and Spaded handles. These handles are designed in a variety of ways to fit into uPVC frames. Each handle type uses an individual spindle to lock the window mechanism. It is essential to determine the kind of handle that is installed on your uPVC windows to ensure that you replace it with the correct one.

You can determine the type of uPVC handle you have by inspecting the base of the handle. There should be a "snap-in cover' over one screw that holds the handle base in place. When you remove this cover you will be able to observe the second screw that holds the handle base in place. Once both screws are removed you should be capable of pulling the handle away from the uPVC window.

After you have removed the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You'll need to purchase a new one that is the same length as the handle that was originally used and locking device.

The spindle wears down and is unable to operate the locking mechanism. This can be due to wear and tear from continuous use or loosening of the locking mechanism, or even corrosion over time. If this happens, you'll have to replace both the window handle and the locking mechanism in order to restore the full functionality of your uPVC Windows.

How do I get rid of my old handle?

Window handles can be damaged or destroyed over time. It is crucial to repair them as quickly as possible to ensure your security. It is good to know that replacing a damaged or worn handle is a relatively simple task that can be carried out in just over a minute and doesn't require any specialist tools.

To remove the old handle, you must first remove the screw located at the base of the handle. After this screw is removed, the handle can then be pulled away from the base. A second screw is situated at the base of the handle. This too can be removed. Once these two screws are removed, the handle can be detached from the base of the window.

Once the old handle has been removed, take the new handle and line up the fixing holes with the holes currently in the window frame. If there is a sticker or cap on the new handle, take it off it if needed and screw the handle into the appropriate position. It is important to check that the handle works once it is put in place. Turn the handle around and make sure that the lock mechanism is working.

Espag handles have an elongated spindle that extends from the handle and slots into a multipoint locking mechanism within the window frame. Cadenza windows have an edge with cut-outs which slot into the lock mechanism, while Cockspur handles have an extended nose that hangs over the frame's outer or transom bar cross-member within the window.

Once you have the new handle in place, insert the spindle inside the lock in the window and then tighten it down. Once the handle is firmly fixed, replace the'snap in' cover and the screw cap (if necessary). The handle is now ready for use, so try opening and closing the window several times to check that it functions correctly and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is simple. You'll need a screwdriver, and a bit of perseverance. The first thing to do is to ensure that the handle is not locked and then take out any screws that are visible. you can also replace these with screw caps if needed. After you have removed the handle, you'll need to take note of the length of the spindle that extends from the back. This is vital because it will determine the kind of handle to purchase.

Espagnolette handles are the most common type of handle for uPVC windows. The spindle is inserted into the handle to activate the locking mechanism within the window frame. When the handle is turned it releases the latch on the window and allows it to open. When used regularly and over time, handles made of espagnolette can become damaged.

Cadenza handles are a form of uPVC handle that is usually used in tilt and turn windows. They feature a protruding blade that operates a multiple-point locking mechanism inside the window. They are more secure than an espagnolette handles because they are able to open from the inside. They can be replaced by the same procedure as espagnolette handles however you must ensure that the new handle has a curved blade instead of one that is flat.

After you have picked the right handle, simply align the new handle to existing screw holes prior to screwing it in place. You should then put the screw covers back on and test that the new handle is working properly. This is done by moving the handle from locked position to the unlocked and the reverse direction several times. It may be worth contacting an expert to see whether you can solve any issues. They can advise you on how to solve the issue in a quick and efficient way.