How to Replace a UPVC Window Handle

If your upvc window handle is broken, don't panic. Replacing a upvc window handle is a fairly simple job and can be completed in just a few steps.

No matter if it's an in-line or a cranked espagnolette window handle each one has an oval spindle protruding from the back plate. This spindle is then fitted into the locking device.

Find out the type and the size of the lock and handle

Over time, window handles or locks may be damaged and lose their functionality. It is possible to repair this issue without replacing the entire uPVC unit. The first thing you should do is identify the type and size of your handle and lock. This will allow you to determine the replacement parts you require.

Identifying the type of handle can be done by looking at the base of the handle. There will be the screw or pin that is holding the handle to its base. If the screw is missing it could be an indication that the handle has broken off from its base section. If the handle has split internally and does not hold onto the spindle anymore it could be a sign that the handle must be replaced.

There are a variety of different types of uPVC window handles The most well-known is the Espag handle. They are usually secured with two bolts and have an articulating spindle that is connected to the lock mechanism within the frame of the window. These handles are usually used on uPVC tilt and turn windows.

Cockspur handles are another type of uPVC handle. Similar to the Espag handle, but they have a low projection from the frame. These handles are typically used on older uPVC window frames.

Venetian window handles are another option. They are similar to Espag handles, but have a flat bottom that allows them be installed flush with the frame. They are an excellent choice for homeowners who want a stylish, elegant handle that blends with their uPVC window frames. The handles are also available in a wide range of colours to match any style.

Take a measurement of the spindle

Before you purchase a new handle, it's essential to understand how the previous one is attached. This will tell you whether it's too tight or loose, and if it's able to fit into the window frame. This can be determined by identifying the handle type and determining the spindle's measurement. The spindle is a steel shaft that connects your handle to the lock on the window frame. The spindle is available in a variety of sizes. The current industry standard is 8mm. Older handles may have a 9mm cross-section therefore it's essential to measure the old one to ensure you get the right size replacement window glass near me.

There are several types of window handles. However, Replace Window Handles the most common are inline Espagnolette and Cockspur handles. These handles are operated by a locking mechanism in the window using shootbolt rods that secure the window when it's closed. They are held in place by screws or pins depending on the kind of handle you have.

You can find replacement upvc window handles on the internet and in many DIY stores. They are available in a variety of finishes and are suitable for both new or replacement windows. For added security they can be key-locking or non-locking in fire-escape.

To remove the old handle simply open the window towards the door and unscrew all screws that hold it in place. Keep the screws in a container to avoid damage. After the screws have been removed, carefully pull out the handle and take a measurement from the base to the tip of the spindle. This will provide you with the information necessary to purchase the correct replacement. The handle's spindle is the shaft of steel that connects it to the lock gearbox in the window frame.

Remove the old handle

Switching the uPVC window sash replacement handle is an easy job that usually takes less than five minutes if you have the appropriate tools. The first step is to identify the type of lock and handle that will help you determine the best replacement. After that, weighing the spindle will make sure that the new handle is a suitable for the job. The handle that was used previously needs to be removed and replaced with the new one.

The majority of uPVC handles are inline Espagnolette handles, which are equipped with central spindles that slot into the window's locking mechanism. They are usually simple to remove, but they might require force if get stuck. The handle is typically fixed by two screws that you can remove using the aid of a screwdriver. It is also possible to remove pins, based on the type of handle.

Once the screws are removed, you can pull off the handle that was previously attached. When the handle is open the top of the baseplate should be visible. It will reveal two additional screws that can be removed. If the sticker is still visible, you'll have to remove it.

You can now screw in the new handle using the screws from the old handle. Make sure the handle is in the open or unlocked position, then align the screw holes with the ones on the window. Once you've done this, you can replace the caps on the screws and then test the new handle to ensure that it functions correctly. The replacement of a uPVC window could be a simple and quick job, but it's important to ensure you complete the task correctly.

Replace the handle with a new one.

It's time to install your new handle if it has been successfully removed the old one from the frame. Begin by finding the screws and then removing them out using a screwdriver. After the screws are removed, put them in a secure place before moving on to the next step.

Then, screw the spindle in by aligning it with the hole that is already in place. Make sure that the holes in the handle with the holes in the window frame. Use screws of the same size as the previous.

The Espag handle made of uPVC is equipped with a spindle that is 7mm square that turns the lock mechanism of the window. This type of handle is utilized in the majority of modern uPVC windows. uPVC Cockspur (also called by the name Cotswold) handles have an extended, curved nose that locks onto the outer frame or cross member of the transom bar. They are often found on older uPVC Windows.

It's important to lock and unlock the window numerous times after the handle has been put in place. If everything goes according to plan, the replacement uPVC handle should be securely attached and working smoothly. If not, the above steps will help you identify any problems and resolve it quickly. Bridgewater Glass can help you in the event of problems with your uPVC handles or any other home improvement that is glazed. Our glaziers are able to repair or replace different window handles and frames. This makes us an ideal option for double glazing.

Test the new handle

In time and with regular use over time, uPVC locks and handles are susceptible to damage and wear and replacement Upvc window Handles tear. They can become less secure and effective and therefore it is important to replace them as quickly as you can. It's also a good thing to do when upgrading your windows. Change the handle and locking mechanism will help maintain your new windows' integrity.

There are a variety of uPVC window handles. Some are fixed by pins or screws, while others have blades that slot into the lock mechanism. Each type has a different way to replace it, so you have to know what type you own.

Espag window handles are the most common kind, and are typically found on the latest uPVC windows. These handles come with spindles that extend from the handle to the lock gearbox and when you open the windows, it activates the locking mechanism. They are also simple to remove. However, you should be cautious not to damage either the mechanism or handle.

Cockspur handles are another alternative for uPVC window handles. They're held by a spur that hooks onto a wedge-shaped striker plate on the frame, and when you close or tilt the window, it triggers the locking mechanism. This type of handle can be more difficult to fix than other types, but it's still a good option for the majority of homes.

Venetian window handles are held with two bolts. They have a slim projection from the frame, which is not the case with the Espag handle. They're ideal if you want an elegant flush handle that blends in with your uPVC windows. These are great for both residential and commercial properties.