Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to decay or rust as aluminum and timber.

It is important to clean and oil UPVC windows and doors regularly. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and even be fatal. It is essential to take the time to ensure that you're doing all you can to keep your windows in good shape.

For single pane windows, it is relatively easy to replace them, and the new window will usually fit inside the frame that was previously installed easily. However, if you have double pane windows that are secured by internal beading it will be more difficult to remove the old panes and put in new ones. In this instance you'll need to find some plastic spacers to aid the new pane in being able to fit properly into the window frame.

If you are going to attempt to remove the glass panes yourself it is important to wear the proper safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a dropcloth before you start working on the glass, so that any shards fall on the fabric instead of onto the floor where they could be trodden under and cause further damage.

It's a good idea to seal the gap after the glass is removed. This will prevent water and drafts from entering your property until a professional comes out to fix the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap is large, you might be interested in an alarm door that comes with an integrated window as this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows with sash. However, with time, they may be afflicted by a variety of problems including sliding. A sagging window in upvc window repairs near me can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it's crucial to act fast to prevent the problem from getting worse.

Repositioning the hinges could aid in fixing a window which is sagging. You'll first need to open the windows to access the frame. You can then unscrew both the hinges on the top and bottom using a screwdriver and adjust the hinges clockwise or counter-clockwise. Once you've adjusted the hinges, close your window and verify the an appropriate fit. If you're happy with the fit, tighten the screws to ensure that they remain in position.

If you cannot reposition the hinges, you might need to replace the seal. As time passes, Window repair rubber seals lose their elasticity and become dry and cause their tightness to decrease. It is important to replace your seal as soon as you can to keep your uPVC Window Repair waterproof and draughtproof.

uPVC handles could also become loose. This is typically caused by screws that have loosened over time, window repair but it could also be due to the mechanism of the handle getting worn out. It's fairly simple to fix a loose uPVC handle. You'll first need to close the window and do a test fitting. The corner joints of the sash need to be aligned with the casing joint. If it doesn't you can use a screwdriver to loosen up the handle. Then, you can turn the mechanism into position.

3. Water Leaks

It is crucial to take action if wake up every morning to discover mouldy walls and floors that are wet. Windows that leak water do are not just a cause for degradation of your home's structure but also hamper your efforts to control the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame is either damaged or is missing.

This is a simple fix that can be accomplished by any DIYer who is competent. Based on the severity of the issue the caulking used previously may need to be removed before a new layer can be applied. When it comes to uPVC repair, it is important to be careful not to over-caulk. This can make your window harder to clean and reduce its energy efficiency.

Check that any drainage holes are free of debris in them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more severe cases, you may need to replace the window.

Other indicators of water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leakage originates from the glass of your double glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. This can be easily fixed by an uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window is difficult to open or it opens with an ease. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Like any mechanical part, hinges can be damaged over time. It is essentially a very simple process, but it's easier to do if you have someone to assist in holding the frame in place.

Make sure that the uPVC hinges open and close in the proper direction. This can be done by checking for the arrows on each hinge. This indicates which way the window should be opened.

The issue can be caused either by opening the window incorrectly or due to a poor installation at the factory. This issue can be fixed by sending us a picture on our website. We will be more than happy to give you suggestions.

Regular lubrication of the hinges is essential. This can be accomplished by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window operate and close more smoothly. It can also lower the possibility of a window getting stuck and stop corrosion. The ideal time to perform this every year. WD40 and other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges, also because of wear and tear, could become misaligned. This causes a gap to form where the sash meets the frame. These can be easily fixed by giving them a good clean, but in the event that they are beyond repair it might be necessary to have them aligned or replaced. The interlock may also become misaligned. This is located on the hinge's side and may need to be cleaned. In certain instances it is possible to replace the hinges.

These seals can wear down or become damaged over time, allowing air escape. Installing high-quality weatherstripping is a good way to stop draughts. Another alternative is to replace the upvc window with glass that is low-emissivity, this will help in regulating indoor temperatures and will lessen the possibility of draughts.

The final method to cut down on the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler which can be hung over your window sill. They will help stop cold air from entering and keep your home warm and cozy!

With a bit of regular maintenance and repair your windows made of upvc will provide excellent insulation and security for your home. However, it is important to recognise that windows last for a certain period of time and eventually, they will reach a point where it is more cost-effective to replace them rather than fix them. So, if you are experiencing problems with your upvc windows, it is recommended to seek assistance from a professional as soon as possible.