UPVC Window Repairs

Upvc windows are able to reduce heating costs and are energy efficient. As they get older, however, issues can occur that need to be addressed. This could be due to damaged hinges, handles, or locks.

Wooden window repair is fairly simple for DIY enthusiasts to tackle themselves. It can also be much less expensive than a brand new replacement window.

Cracks

Cracks and fractures in uPVC windows can be a serious issue. Unrepaired windows can cause water intrusion, less effective barriers to cold weather, and even structural damage. Find a local builder who specializes in repairing uPVC frames. They must possess the necessary knowledge and experience as well as the right equipment to ensure the most effective results. This will ensure your crack is repaired swiftly before it gets worse, and you won't have to replace your window unit or glass.

Small cracks in glass can be fixed with a range of home-based solutions. Masking tape and superglue are two of the most common solutions to hold glass damaged in position for a short time. For more severe cracks, the tape may need to extend beyond the crack on both sides to achieve the optimal results.

You can also use two-part epoxy to repair broken or cracked glasses. Most hardware stores sell this product for around $10. Make sure your workspace is prepared before mixing the epoxy. Also, ensure you have all the equipment required for the job.

If your upper or lower sash is difficult to raise, it's likely because the cords that connect the sash's weights have been damaged. This is an easy fix that can be done using a ladder and a flathead screwdriver. A drip cap that is rotten can be easily repaired at home. The majority of home centers have a drip caps that are not rot free and can be easily nailed or caulked to be fixed. Check that the glass of double glazing or triple-paned window is not broken. This is due to the gases that are filling the space between the panes contribute to improving energy efficiency and should be kept, not escaping.

Water Leaks

If your uPVC windows leak, it could damage the interior of your house and cause costly repairs. Water leaks can also weaken the structure of your home and lead to the growth of mold. To avoid the damage, it's essential to repair any issues caused by leaky windows immediately.

The most common reason for window leaks is the damage to the sealant around the frame. Utilizing silicone caulk can help restore the condition of the seal back to its normal condition and stop water leakage. It's also important to look for cracks and gaps around the frame as well in the stone or brick walls that surround your windows.

A blocked drainage hole or an issue with flashing are the other two typical causes of windows leaking. Make sure that the drainage holes haven't been clogged or blocked, especially after a heavy downpour. It's also a good idea to inspect the flashing that runs around the bottom of your window and make sure it's properly sealed.

Lastly, it's important to make sure that your drip cap isn't missing or rotten. A rotted or damaged drip cap can let water in the window from above, causing damage to the structure of your home. Replacing drip caps isn't an arduous task and is typically a simple task of buying a new one and nailing it into the correct position.

A professional can also test your windows for watertightness. They can use a tool to determine the water-tightness of your windows and ensure that they meet the standards of the industry. If your windows don't pass the test, uPVC repair you will have to replace them. It's a costly repair but it's is worth it to ensure the safety and security of your family.

Sagging

If your windows don't shut properly, it could cause a number of issues, such as drafts condensation, and an increase in energy bills. It could also mean that the windows weren't installed correctly or uPVC repair the sealant is worn out. There are fortunately, a few options to fix the problem.

To fix your window properly it is necessary to set up a work space with plenty of natural light. Start by laying newspaper or an old blanket on the floor to protect it from drips or splinters that could be leaking from the window as you work.

You will also want to make use of a white cloth that has been soaked in a solution of water and detergent. This will ensure that you don't leave any color stains on your windows. Note the location of the hinge channel on your uPVC window when you are ready to begin working. Then unscrew the channel from the frame and fill the screw holes with epoxy (for uPVC windows) or wood filler (if frames are constructed from wood). Make sure to smooth out the hole before it sets.

Install the hinge channel after the holes are filled. Make sure you center it on the window jamb and drill the screw holes about a quarter-inch away from the original locations.

Then, take a measurement of the length of the spindle that protrudes from underside of the handle and then order a replacement online or bring your old one to an hardware store to get a matching. Then, pull out the setscrew that was on the shaft of the operator and file it flat so the set screw is able to secure itself to the shaft (photo). Now your uPVC windows should be closing easily.

Broken Hinges

There will be a problem opening or closing your uPVC windows if the hinges are broken or aren't functioning properly. This could cause problems with security and prevent your home from remaining warm or cool. It's easy to get a new window hinge for your uPVC windows. It's essential to ensure that you have the right type of hinge for your windows.

The hinges have to be identical in size to fit into the frame of the window. The most commonly used hinges for windows made of uPVC are standard 18mm or UPVC 15mm hinges for windows. There are also hinges specifically designed for wooden frames. The right type of hinge will allow you to avoid common problems with your windows.

There are a variety of reasons the hinges on your windows be loose or stiff. One common cause is that the hinges aren't sufficiently tightened. You can check this with a screwdriver. locate the friction screw at the end of the hinge, and then loosen it. Then, you can adjust it by turning it in either direction.

Call Preston Glass Fix if your UPVC window's hinges don't work correctly. We can offer a quick fix. Our technicians will examine the condition of your window hinges and advise you on the best option for you. We can replace the window hinges, re-tension them or install new locking mechanisms to ensure that your UPVC windows are secure and safe for a long time to come.

Faulty Locks

UPVC window mechanisms and locks are an important part of security for your home. They make it difficult to open windows without breaking into the house. It can be a hassle when a lock malfunctions, however, you don't have to replace the entire window.

It's usually an issue that is minor and could have been easily avoided with regular maintenance. This is why we recommend having your upvc Repair windows maintained regularly using our annual maintenance program to minimize the risk of issues.

The majority of modern uPVC windows have espagnolette locks that work by pushing the nose of the handle across a wedge block then turning the handle to close the lock. They are very efficient in keeping the window closed, however over time, they could begin to fail if they are not properly maintained. We suggest using WD-40 for lubrication at least once per year.

If you notice your uPVC window isn't opening or closing as quickly as it did in the past, or if the lock doesn't work properly, there may be a problem with the locking gearboxes within the frame. It can be difficult to access this because it requires the removal of the seals that surround the frame and removing the handle (be careful not to scratch these).

A locksmith who specialises in UPVC repairs has the knowledge to quickly identify the issue and will then be able replace the failed locking gearbox with an exact replacement. This simple and quick fix can save you hundreds of dollars by not having to purchase new windows.