Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel to it thanks to its larger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models may be a bit firm at times. The front tyres could lose grip on rough surfaces, and its CVT may occasionally exhibit wrist-flexing torque steer.

This is typically caused by an inoperable coin battery, which can be easily replaced in minutes. Make sure the replacement battery has the same voltage, size and specifications.

Water Damage

Water damage is among the most frequent causes for a Nissan keyfob to display the "key ID incorrect" message. The key fob has rubber seals which protect the chip inside, but long-term exposure to moisture could cause it not to function properly. This is typically the case in the event that you've dropped your key fob into the ocean or into a swimming pools, but it could happen when it's wet due to rain or soapy hands.

If your key fob was exposed to water for the course of a long time, you may need to clean it with isopropyl, or an electronic cleaner. It may also require the attention of a specialist for repair or replacement.

If your key fob needs to be replaced, it's quite simple to do. First, ensure you have a multipack of the right battery (CR2032 3V). The front and rear cases using the flat-head screwdriver. Remove the metal clips, then remove the old battery and replace it. After reassembling your fob, put the mechanical key back into place and verify that it is working correctly. If it does not it is necessary to go to your local Nissan dealer or an expert auto locksmith to fix the chip on the key. The chip is not usually damaged by water, so it shouldn't be too expensive.

Dead Coin Battery

The coin battery is a second common reason for why your Nissan Qashqai remote key fob won't work. The batteries typically last between 3-5 years, but they are susceptible to becoming depleted in time, particularly if the fob is frequently dropped. It is possible to replace the battery with a fresh one, but make sure it's the same voltage and size as the original. If you're using an alternative battery, it could cause the key to have an untrue key ID, which can prevent it from paired with your vehicle.

The most effective method to replace the battery of a coin on a Nissan Qashqai key fob is by removing the key fob using the small screwdriver with a flat-head. Push in the screwdriver in tiny notch at the bottom of the fob, and turn it around gently to separate the two parts of the key fob. Then, take out the old CR2025 button cell battery and insert another one after confirming its location on the fob.

Before putting the new battery into place check to ensure there is no water damage or dirt on the terminals. If this is the case clean the terminals with the smallest amount of isopropylethanol. You should also ensure that the pole cables are plugged in correctly - they should be connected to the positive and negative poles of the battery respectively.

Troubleshooting

If your nissan key programming Qashqai key fob stops working after exposure to pure rain or tap water, it may be a sign of an internal chip problem. You'll require a new fob if you can't solve the issue by changing the battery. If you dropped the key fob on the ground and it stopped functioning immediately it's likely because it damaged the internal chip. It is possible to get the key fob to function once more if you remove and clean the chip using alcohol and paper towels and then insert it back into.

A common error that you might see on the dashboard of your vehicle is "Key ID Incorrect." This means that the vehicle cannot recognize the key fob and not allow it to start the engine. This issue can be caused by many different ways, including water damage, problems undetectable in the key fob circuitry or RFID interference.

The key fob will cease to function when the 12 volt batteries are dead or fail to provide enough electric current. This can affect the Nissan Qashqai's remote keyless system central locking, as well as the ability to start the engine using the key fob. If you're unable to unlock or lock the door manually you must check the batteries in your key fob to make sure they're in good shape. You could also try installing the battery again to reset your transmitter.

Reprogramming

If the key fob is not been submerged in salt water the key fob should be able to return to life after a quick rinse with clean water. You could also try cleaning the electronic chip using isopropyl Alcohol or an electronic cleaner. If none of the above works it is possible to replace the key fob.

If your Nissan Intelligent Key is still not working, there could be an issue with the connection between it and your car. To reconnect it, start by turning the key in the ignition without starting the car. Continue to do this until you see the hazard lights flash twice. Then, turn off the vehicle and remove the key.

Open the fob compartment in your vehicle's fob compartment. It's usually on a door's jamb or the handle of the door for the driver. Find the small "program" button and press it. You will hear a chime after the process is completed.

Now that your Intelligent Key is relinked to the car, it's time to test it out. Make sure you press all the buttons on the key while standing a distance from the vehicle. If the lights flash and the horn beeps it means that the key has successfully connected to the nissan key fobs (written by Bestone Korea). It is also possible to test it in close proximity.