Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism faulty? Maybe the window or door handles don't meet up correctly or are difficult to use.

You'll lose energy in the event that your double-glazed doors fail to work properly. This also increases the risk of burglary. Owen the Locksmith will be able to fix your door lock at a reasonable cost.

Snapped Key

If a key is snapped off inside a lock, it could be incredibly difficult. It could also be a security risk since the door might not lock and could leave you open to intrusion. There are a few quick solutions you can use to resolve the issue and make your door work again.

First, remember to stay calm. If you panic and start poking around wildly, you might just end up pushing the damaged piece of the key deeper into the lock, making the situation even more difficult.

Spray WD-40, or another penetrating lubricant into the lock. This will assist the broken piece come out more easily. You can also use a screwdriver to break any pieces stuck. If you have a part of the key that is stuck out, grab it with a paperclip or another thin metal object and pull it. Both methods work, but you must be careful not to push the damaged key further into the keyway.

Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades can also work well for this. If you don't happen to have one of these tools, you can bend a hook with needle-nosed pliers. You can also make use of a pair of tweezers to grab and remove the remaining pieces of broken keys.

If you can't get the broken piece of key out, you can try using a lock de-icer. It is found in most hardware stores, and it works by freezing any moisture or ice that may be inside the lock.

If none of these solutions seem to work, it may be time to contact a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles or snapped keys with uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are easier to use. Get a double glazing repair with us online, or give us a call to discuss your needs.

Broken Cylinder

A damaged cylinder could pose an extremely risky security issue. A professional locksmith can easily fix the cylinder. A locksmith will have to tap the cylinder in order to repair it. This can be done with a hammer or other tool. However, the best method is to use a wire or a long match. Then, put the match's tip or wire near the keyway. The locksmith can then strike the lock in order to crack it. This is more secure than using a hammer, which can harm the lock.

The most frequent cause for cracks in the cylinder head is overheating. This can occur when the cylinder block and head are made of different metals, like cast iron and aluminium. When different metals heat up and cool down at different rates, it could cause localised hotspots that expand faster than the rest of the cylinder head, thus leading to cracks.

Corrosion is another possible cause of cylinder fractures. If the head and block of the cylinder are not maintained correctly they could be corroded or rust, which can cause them to expand faster than they would normally. In time, this could also cause cracks.

If your uPVC window or door lock is stiff and requires a lot of pressure to turn, it could be due to a variety of causes. This problem can be caused by a malfunctioning locking mechanism, or misalignment or a worn-out handle.

Fortunately it's a simple and inexpensive fix for most double glazing owners. A professional locksmith will typically be able to resolve this issue within a matter of hours after arriving at your residence. Depending on the needs of your home they can change the locking mechanism, replace the window handles, or change the gearboxes. A professional locksmith will always be able advise you on the most cost-effective solutions for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which give you an extra layer of protection from burglars. This is a small cost to pay for the security that comes with knowing your uPVC doors are secure.

Broken Handle

Window handle locks are complex mechanisms that deteriorate with time and use, so it's not a surprise that they sometimes break. It isn't easy to determine the reason behind the problem and fix it correctly.

Fixing your broken handle, whether it's an internal latch or locking mechanism will increase the security of your uPVC door and prevent draughts. If you do not repair or replace your handle can be expensive and could harm the door's frame as well as lock It is therefore worth taking the time to do it right.

Screwdriver Open the window and the screw loose, loosen the handle. This should be located on the inside face of the back plate, normally concealed by an attractive cover for the screw for aesthetic reasons. Be sure not to lose any of the internal components within the handle, such as the plates or levers on either side of the spindle. It is best to keep them in the same place so you can re-install them in the event of a need.

Then, using a second screwdriver loosen the screw that holds the handle to the spindle on the back. Once the screw is loose, you can remove the handle and take the broken spindle out. Replace it with a brand new spindle, ensuring it's the same length (you can buy them on the internet or at hardware stores). Securely screw it in the frame. Be careful not to tighten too much because this could cause damage to the handle or the window frame.

Check that the new handle is installed Close the window and test the handle. It should function smoothly and you'll be able to open your windows after a few times.

While you're working on the handle, make sure to ensure that your uPVC windows are shut correctly. If they don't, you could experience damp and draughts in your home as well as compromising your home's energy efficiency. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames so they shut correctly.

Broken Spindle

It is quite common that the spindle within the handle breaks, rather than the handle itself. This is particularly common in uPVC tilt and turn windows. These kinds of windows require a handle that acts as a locking mechanism within the frame of the window replacement Near Me. The handle is attached to a central rod which triggers a set of mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism is not able to open when the handle is turned, it is likely that the spindle has been damaged This can be an extremely frustrating issue.

There are solutions to this problem. A reputable locksmith will be able to quickly and effectively fix this problem. They can remove the window handle using a tool that can remove the wheel component of the mechanism where the spindle goes. This can be done with no damage to the handle or the window frame.

After removing the wheel, the technician can inspect the spindle to determine what caused it to break. This involves disassembling the spindle, and then examining each component part, noting any damage or excessive wear. This process is typically done in a clean room by skilled technicians.

The next step is to clean the damaged spindle, this helps eliminate any debris or dirt that could be hindering its normal functioning. Following this, the spindle can be repaired or replaced. If the technician is replacing the spindle, the dowel can be used that is similar in size to the original. He will then drill matching holes into both pieces. This will ensure that the spindle will fit perfectly with the handle.

If the damaged spindle can't be repaired it may require replacement completely. Home centers sell generic replacements. However, if the style of your window is unique then you will need to find a woodworker or cabinet maker who can duplicate the exact component for you. After the spindle is installed, it can be attached to the handle. Place the screw holes on the handle to the existing screws in the frame. Once the new handle is firmly installed, you are now ready to operate your uPVC window.