Double Glazing Door Lock Repairs

Have you noticed that your uPVC window or door mechanism become faulty? Maybe the handles on your uPVC windows or doors aren't aligned correctly or are difficult to operate.

It's important that the double glazed doors operate smoothly, otherwise you'll be wasting energy and increase the chances of burglary. Owen the Locksmith will be able to repair your door lock at a reasonable cost.

Snapped Key

It can be frustrating when a key gets stuck into the lock. It could also be a security problem because it could leave you vulnerable to burglars if your door does not lock. There are a few quick fixes you can make to resolve the issue and get your door working again.

First, remember to stay calm. If you panic and begin poking around wildly you may end up pushing the broken piece of the key even further into the lock, thereby making the situation much worse.

Spray WD-40, or any other penetrating lubricant, into the lock. This will help the broken piece to be removed more easily. You can also use a screwdriver to help break up any pieces stuck that might be blocking the way. If you're lucky enough to have a little bit of the key left sticking out, you can use a paperclip or some other metal object that is thin to grab it and pull it out. Both methods are effective, but you need to be careful not to push the broken key further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have one of these tools you can bend a hook with needle-nosed pliers. Finally, a pair of tweezers can be used to grip and pull out the last part of the broken key.

If you cannot remove the broken key piece Use a lock deicer. It is available at most hardware stores. It works by freezing any moisture or ice that might be in the lock.

If none of these strategies are working, it might be time to call in locksmith. Fitlocks experts can quickly fix problems with uPVC door locks and mechanisms that have snapped keys as well as broken handles. They can also reconfigure double glazing door mechanisms to ensure that they are easier to use. Book a double glazing repair through us online or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a serious security risk. A locksmith professional can fix the cylinder. To fix the cylinder, a locksmith will need to tap it. This can be accomplished with a hammer or other tool. The best method is to use a wire or a long match. Then, position the end of the match or RepairMyWindowsAndDoors wire near the keyway. The locksmith will strike the lock to crack it open. This is much safer than using a hammer, which could damage the lock.

The most frequent cause of cylinder head cracks is overheating. This can occur when the cylinder block as well as the cylinder head are made of different metals, like cast iron and RepairMyWindowsAndDoors aluminum. When the different metals heat up and cool down at different rates, it may cause localised hotspots that expand faster than the rest of the head of the cylinder, leading to cracks.

Another possible cause of cracks in cylinders is corrosion. If the head and block of a cylinder are not maintained properly, they can rust or corrode and cause them to expand faster than expected. In time, this could cause cracks.

If your uPVC window or door lock is rigid and requires a lot of pressure to turn, it could be due to a variety of reasons. A faulty locking mechanism, misalignment or a worn handle are common reasons for this issue.

Fortunately it's a simple and inexpensive fix for most double glazing owners. A professional locksmith will usually solve this issue within an hour of arriving at the property. Depending on the needs of your home they can change the locking mechanism, change the window handles, and also change the gearboxes. A locksmith with experience will always be able advise you on the most cost-effective solutions for your home. They can also suggest upgrades to 3 Star security TS007 euro cylinders that will add an extra layer of protection against burglars. It's a small price to pay for the security that comes from knowing that your uPVC doors are safe.

Broken Handle

It's not surprising that window handle locks may break. They have intricate mechanisms that become less effective over time. It isn't always easy to pinpoint the cause of the problem and then fix it properly.

If the issue is in the internal locking mechanism or RepairMyWindowsAndDoors the latch, fixing your broken handle can improve your uPVC double glazing door's security as well as help you stop drafts. It could be costly to replace or repair your handle if it is not done correctly and could also harm the frame and the lock of your door.

With the window in the open position and the window open, loosen the screw that secures the handle by using a screwdriver. The screw should be on the inside face of the back plate, and is normally covered by a screw cover for aesthetic reasons. Be sure to not lose any of the internal parts within the handle, such as the plates or levers that are on either side of the spindle. Keep them in the same order to make it easier to replace if necessary.

Next, turn the handle until it's 90 degrees towards the window frame. Then, loosen the screw at the back of the handle which holds it to the internal spindle using a second screwdriver. Once the screw is released, you'll be in a position to pull the handle off and take out the broken spindle. Replace this with a new one, ensuring it's the same length as the old one (you will typically find them on the internet or in hardware stores) and then securely screw it into the right place. Don't over tighten the screw because this could harm the handle as well as the window frame.

Ensure the new handle is installed Close the window and test the handle. It should function smoothly, and you will be able to open your window after a few times.

Don't forget to double-check that your uPVC window repairs near me is closing properly while you're working with the handle. If they aren't closing properly, you could experience draughts or damp in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can adjust the hinges on your window frames to ensure they close correctly.

Broken Spindle

It is more likely for the spindle to break than the handle. This is particularly common with upvc door repairs near me tilt-and-turn windows. These windows require a handle to operate an locking device within the window frame. The handle is connected to a central rod that triggers the mushroom-shaped locking cams that lock into the window frame keep. If the dead latch mechanism is not able to open when the handle is turned, it is possible that the spindle is broken and this could be a frustrating problem.

Luckily, there are steps that can be taken to remedy this situation. A good locksmith will be able to quickly and effectively fix this issue. They can remove the window handle using a tool that can remove the wheel portion of the mechanism, where the spindle goes. This can be done without damaging the handle or causing other damage to the window frame.

After removing the wheel, the technician will inspect the spindle and identify the cause of the break. This involves breaking down the spindle into its component components and carefully observing their general condition as well as any particular areas of wear or damage. This process is typically carried out in a clean, well-lit room by highly skilled technicians.

The next step is to clean the damaged spindle, this helps eliminate any debris or dirt that might be hindering its normal function. The spindle can then be repaired or replaced. If it's being replaced, the technician could use the dowel that is similar in size to the one used in the first and drill mating holes into both pieces of the spindle. This will ensure that the new spindle is an exact fit with the handle.

If the damaged spindle is beyond repair, it could be necessary to replace it entirely. Home centres sell generic substitutes but if the window design is unique then you'll have to speak with an expert in cabinet making or woodworking who can replicate the exact piece. After the spindle is installed, it is attached to the handle. Line up the screw holes on the handle to the existing screws in the frame. Once the new handle is firmly seated you will be ready to operate your uPVC window.