Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. In contrast to aluminium and timber, they don't corrosion or rot.

It is essential to clean and oil UPVC windows and doors on a regular basis. This will help prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and even be fatal. It is important to ensure that your windows are in good working order.

For single pane windows, it is relatively easy to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. If you have double-paned windows that are joined by internal beading, it is difficult to remove and replace the old panes. In this case it is essential to purchase plastic spacers in order to make sure that the new pane fits into the window frame.

If you are going attempt to remove the glass panes yourself it is crucial to wear appropriate safety gear such as gloves that are thick and protective eyewear. You should also lay down a drop cloth before you begin working on the window panes, so that any shards fall on the fabric and not onto the floor, where they could be trampled.

It's a great idea to tape the gap once the glass is removed. This will prevent drafts and water from entering your home until a professional arrives to repair the window. It also acts as an obstruction to prevent criminals from getting into your home. If the gap between the window and the door is substantial, you may prefer security screens that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are an affordable energy efficient, durable and long-lasting alternative to timber windows with sash. However, over time they may be afflicted by a variety of problems including sliding. A sagging upvc window repair windows can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to lose its shape, it's crucial to act fast to prevent the problem from worsening.

To repair a window that is sagging, you can try to reposition the hinges. To do this, Window Repair you'll need to open the window to access the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust them clockwise or window repair counter-clockwise. Once you've adjusted the hinges, shut your window and check for fitting. If you're happy with the fit, you can tighten the screws to ensure they remain in position.

If you are unable to move the hinges, you might need to replace the seal. Seals made of rubber can dry out and lose their elasticity over time, causing them to loosen. If this happens, it's essential to replace the seal as fast as possible so that your uPVC windows are waterproof and secure from draughts.

UPVC handles can also loosen. This is usually due to screws that have been removed over time, but it can be due to the mechanism of the handle wearing out. Luckily, it's not difficult to fix a loose uPVC window handle yourself. First, you'll need close the window and then perform a test to ensure that it fits. The corners of the sash should be aligned with the casing joint. If it isn't then you can make use of a screwdriver to loosen the handle and return the mechanism to its original position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it's crucial to take action. Windows that leak water do not only lead to the destruction of your home's structure but also hinder your efforts to regulate the temperature in your home. The most common cause for leaking uPVC windows is that the sealant surrounding the frame has been damaged or missing.

This is a fairly simple fix and should be undertaken by any competent DIYer. Based on the severity of the problem the caulking used previously might need to be removed before a new layer can be applied. It is important to keep in mind that when it is about uPVC Window repair repairs you should avoid the temptation to "over-caulk' as this will only make the area harder to clean and could reduce the efficiency of your energy.

It is important to check that the drainage holes are clear of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious cases you might need to consider replacing the window.

Other indicators of long-term water leakage include rotted sills and the appearance of black spots of mold on the wall near the window. This fungus thrives in humid conditions and can propagate quickly throughout the house.

If the leakage occurs between the double glazed window repairs-glazed glass it is more likely that the issue is with the seal than the frame. It is also possible to be fixed by an uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and open with a breeze, it may be hinges at fault. Any competent DIYer can replace hinges in just a few minutes.

Nearly every home in the UK will have top-hung or side-hung uPVC windows that have hinges and like any mechanical part they can wear down over time. It is essentially a very simple process but it can be easier when you have a person to help you hold the frame up.

Make sure that the uPVC hinges are closed and open in the correct direction. You can do this by looking for the arrows on each hinge. This indicates the direction in which the window should open.

Faulty window hinges can be caused by incorrectly opening the window a certain way or due to improper installation in the factory. Sending us a picture via our website is often enough to solve the issue. We are more than happy to give assistance.

Regular lubrication of the hinges is essential. This can be accomplished by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regular lubrication can allow the window open and close more easily. It also decreases the chance of windows sticking and help prevent corrosion. This must be done at a minimum every year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by different factors. Firstly the hinges, again due to wear and tear could become misaligned. This will cause gaps to develop where the sash meets the frame. If they're beyond repair, it may be necessary to have them realigned. The interlock, which is on the hinge side of the window, may also become misaligned, again it is possible to just give them a clean but in some instances it could be necessary to have them replaced.

The second most frequent reason for draughts is window seals, these are susceptible to being worn out or damaged over time, and let air escape through the gaps. Replacement of these with high-quality weatherstripping will help to prevent draughts. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures and lessen the risk of draughts.

Lastly, one of the most effective methods to reduce draughts is by using an draught excluder. These are typically fabric tubes which are filled with a kind of filler. They can be put on top of your windowsill. They can help block out cold air and keep your home warm and cosy!

With a little regular maintenance and repair your windows made of upvc will continue to provide a great level of security and insulation for your home. It is crucial to recognize that windows last for a certain period of time and they may reach the point when it's more efficient to replace them than repair them. If you are experiencing issues with your window made of upvc it is recommended to speak with a professional immediately.